Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Husqvarna Dateigröße: 1.87 mb Dateiname: HOUS2009_115149727.pdf Unterrichtssprache:

• Checkbrakeoperationfrequently.Adjustand service as shown in the Operator’s Manual. WARNING! WARNING! 7 UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. TOOLS REQUIRED • 7/16" Wrench or ratchet and socket • ." Wrench or ratchet and socket • 7/8" Socket • Torque Wrench • Phillips Head Screwdriver • Hacksaw • Pliers • Drill and 7/8" bit NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the mower in the operator’s position. Upper Chute Bag Dump Indicator Blower Housing Middle Chute CONTAINER CONTENTS • Blower Assembly • Drive Pulley • Belt Shield • Belt • Mounting Bracket • Bag of Hardware • Weight Belt Cover CAUTION BEFORE ASSEMBLING GRASS CATCHER TO MOWER: • Set parking brake. • Place motion control levers in “NEUTRAL” position. • Turn ignition key “OFF” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug and place wire where it cannot come in contact with plug. 8 1. Remove the discharge chute from the deck. (Deck configuration will vary by size and model) 2. Lower deck to the lowest cutting position. 3. To prevent interference with the new belt shield, reverse the bolt/nut assembly on the rear of the deck height adjustment plate. 4. Remove the right hand (discharge side) belt cover from the deck. ASSEMBLY 1INSTALLING DRIVE PULLEY 2MOUNTING BLOWER ASSEMBLY Outer Pulley Cover Pin Hairpin Cotter Deck Height Adjustment Belt Cover 1. Install the front mount bracket to the deck with the pin and hairpin cotter supplied with the kit. Discharge Chute Reverse rear bolt/nut assembly 5. Remove the bolt securing the right hand deck pulley to the spindle. 6. Replace right blade shaft with new, longer shaft. The existing drive pulley and key will fit on the new shaft. Install blower drive pulley with the raised portion of pulley hub down. Slide spacer inside new pulley. Add key to new pulley. 7. Remove two rear bolts from spindle and place belt shield standoff where the two bolts were removed. Replace bolts and tighten. Drive Pulley Key Replacement Shaft Belt Shield Standoff Spindle New Heavy Washer New Bolt Spacer 8. Use heavy washer and bolt supplied in kit to attach pulley to spindle. Torque to 55-75 ft/lbs. 9. Reinstall the deck belt. 9 ASSEMBLY 1. Make sure the tension release lever is forward or disengaged. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release arm to the rear and engage in the latch. 4INSTALLING DRIVE BELT Rear Of Deck Idler Pulleys Outer Pulley Twist in Belt Tension Release Arm 5INSTALLING BELT COVERS 1. Place the deck belt shield on the deck over the drive pulley and secure with hardware removed from steel belt shield. 2. Place retainer on the outer pulley cover. 3. Align the tab end of the belt cover into the slot on the deck belt shield and the other end over the end of the outer pulley cover. 4. Secure with knob. Retainer Knob Outer Pulley Cover Deck Belt Shield Belt Cover Tab Middle Chute Latch 1. Temporarily secure the hold down bracket to the skid plate, using a bolt and nut from the kit and the outer hole in the bracket. If needed, prop the blower housing up so it sits vertically level, but leave no more than an 1/8" gap between the deck and blower housing. Skid Plate Back-up Plate Back-up Plate 3INSTALLING HOLD DOWN BRACKET 2. Using the back-up plate as a template, drill holes in blower housing through the slots on the hold down bracket. Drill in the middle of the bracket slots to allow for adjustment if needed. Remove hold down bracket. 3. Remove blower housing. Place back-up plate inside the blower housing, lining up new drill holes and back-up plate. Install the hold down bracket by inserting bolts from the inside, through the blower housing and into the bracket slots. Secure with flange nuts. Hold Down Bracket Hold Down Bracket Hole 10 ASSEMBLY 6TRIMMING MIDDLE CHUTE 7INSTALLING BAGGER MOUNT 1. Using the hacksaw, trim along the dashed line. 2. Locate the middle chute, flat washer, hood latch, weld nut, lock washer and machine screw from kit. 3. Install in the appropriate hole at the upper end of the middle chute, according to deck size. Trim Line Hood Latch Weld Nut Machine Screw Lock Washer Latch Location Flat Washer 7INSTALLING MIDDLE CHUTE 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. Middle Chute Blower Assembly 1. Using hardware provided in kit, attach support mount to unit. 2. Attach hanger bracket to support mount. Do not fully tighten nuts at this time. Hanger Bracket 3. Secure rear end of support straps to outside of hanger assembly. Set reinforcement plates to the outside of the tank brackets and fasten front end of support strap to tank bracket and reinforcment plate with round head bolt. Secure front end of reinforcement plate to tank bracket with hex bolt. Fully secure all mounting hardware. See illustration...

Herunterladen

Geben Sie zwei Ziffern: