Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Dixon Dateigröße: 1.49 mb Dateiname: Unterrichtssprache:

2. Locate the middle chute, flat washer, hood latch, weld nut, lock washer and machine screw from kit. 3. Install in the appropriate hole at the upper end of the middle chute, according to deck size. 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. 8 Remove plastic end caps from the center bag support arm. Fully insert spacer plug into the end of the support tube. It may be necessary to tap the spacer into place with a hammer or mallet. Replace the plastic end cap back over the spacer. The additional extension will hold the hood more securely when latched. NOTE: Assistance from another person may ease mounting the cover assembly to mower. 1. Lift and rotate cover to align the cover brackets with support assembly tubes. 2. Slide the cover down over the support tubes until secure. Remove center end cap Insert spacer and replace cap ASSEMBLY 7INSTALLING BAGGER MOUNT 8MOUNTING COVER ASSEMBLY 9INSTALLING SPACER PLUGS 1. Using hardware provided in kit, attach support mount to unit. 2. Attach hanger bracket to support mount. Do not fully tighten nuts at this time. 3. Secure rear end of support straps to outside of hanger assembly. Set reinforcement plates to the outside of the tank brackets and fasten front end of support strap to tank bracket and reinforcment plate with round head bolt. Secure front end of reinforcement plate to tank bracket with hex bolt. Fully secure all mounting hardware. See illustration. NOTE: Rear guard hole may need to be drilled out to 5/16" if kit hardware is too large. Hanger Bracket Support Mount Support Straps Reinforcement Plate Hex Bolt Placement Round Head Bolt Placement 9 ASSEMBLY 1. Install containers on support frame, overlapping containers at center tube. Note: One container should always overlap the other container at the center tube. 2. Close cover and lock latch handle over support tubes. Support Frame Latch Handle WARNING! DO NOT operate mower unless containers are properly installed. Containers are subject to wear and deterioration. Check containers frequently, replace when cracked or damaged. Use only a recommended replacement containers. 11CHUTE/HOOD INSTALLATION 10CONTAINER INSTALLATION 1. Latch upper chute to middle chute. 2. Insert upper chute into gasketed opening on the hood assembly. OPERATION TIPS FOR IMPROVED BAGGING Follow the mower operation instructions in you mower operator’s manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regular use of your grass catcher. • Always run throttle at full speed when bagging. • Select a speed low enough to give good mower cutting performance, good quality cut and good bagging performance. NOTE: It may be necessary to overlap width of cut to suit your conditions. • If grass is extremely tall, it should be mowed twice. The first time relatively high, the second time to desired height. • Use left hand side of mower for trimming. • Plastic trash bags (3.0 mil, 30 gallon) can be inserted inside grass catcher containers for ease of debris disposal. To remove the plastic trash bags when full: a. Disengage blades, shift into neutral, engage the parking brake and stop the engine. b. Unlatch and raise cover. c. Remove one container at a time by grasping container handles and pulling toward the rear, off of the tube rails. d. With the container resting on the ground, close and secure the top of the plastic lawn bag. e. Tip the container on its side and slide the filled bag from the container. f. Install a new plastic lawn bag with the edges of the bag draped over upper lip of the Container (for replacement bags refer to REPLACEMENT PARTS). g. Repeat for other container. h. Reinstall containers making sure right container overlaps left container at center supports. i. Close cover and secure latches over center support tubes. • Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging. • If the grass catcher fails to pick up cut grass or leaves, it is an indication that clogging has occurred in the system or that the grass catcher containers are full. a. Disengage blades, place motion control levers in neutral position. -Unlatch and raise cover. -Slide out containers and dispose of clippings. -Replace containers, close cover, and latch. b. Unlatch chutes and check for clogging. -Remove all debris in chute. -Reassemble and latch chutes. GENERAL RECOMMENDATIONS Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE • For best results mower blades must be kept sharp. Replace bent or damaged blades. • See BLADE CAR...

Herunterladen

Geben Sie zwei Ziffern: