Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Bolens Dateigröße: 1.14 mb Dateiname: Unterrichtssprache:

Do Not allow exaust to be pointed in the direction of persons. 3 I FIGURE 1. ASSEMBLY INSTRUCTIONS CONTENTS OF HARDWARE PACK: (See Figure 1.) A (2) Carriage Bolts B (2) Hand Knobs C (1) Hex Sems Bolt NOTE Vacuum hose attachment 244-204-000 comes with model 694. It is optional equipment on all other models. \ % FIGURE 2. PARTS IN CARTON (See Figure 2): D (1) Upper Handle E (1) Directional Discharge NOTE USE THIS HOLE ONLY The right and left side of your leaf blower is determined from operator's position. 1. Remove the leaf blower, hardware pack and all literature from the carton before discarding carton. 2. Figure 3 shows lower handle. Upper handle mounts in center hole only. FIGURE 3. 4 \ FIGURE 5. OPERATION BEFORE STARTING ENGINE Service engine with gas and oil. See engine manual packed with leaf blower for complete instructions ! for care and maintenance of engine. READ DIREC-1 TIONS CAREFULLY. TO START ENGINE 1. Move throttle to "START" position. 3. Place the upper handle (D) over the lower handle, lining up the holes. Secure with carriage bolts (A) and hand knobs (B). See figure 4. 4. Slip end of directional discharge (E) over chute opening. Secure in position with hex sems bolt (C). See figure 5. 2. Pull starter rope once with quick, full stroke. Move hand throttle to "FAST" position and pull starter rope again. 3. When engine starts, move throttle to "RUN" position until engine warms up. TO STOP ENGINE Move throttle control lever to "OFF" position. I ADJUSTMENTS Î Do Not make this adjustment or any adjustment with the engine running. Stop the engine, disconnect the spark plug wire and ground plug wire to engine block. TWO-WAY AIR DISCHARGE Your leaf blower is equipped with an adjuslable chute deflector. Simply push down on handle provided and swing door towards the front or side as des red. See figure 6. ipf IRECTIONAL DISC^tARGE HAIM JLE HEIGHT ADJUSTMENT To adjust the height of the discharge, stand on the right hand side of the leaf blower and move the irdex handle towards the engine. Move handle towards rear of unit to lower height. Move the handle forward to raise the height. See figure 7. MAINTENANCE AND LUBRICATION Your leaf blower, like all machines with moving parts, must receive care and maintenance. The following tips, if used, will contribute many troublefree hours to your blower. 1. Check oil level frequently. When changing oil, make sure dirt and debris is cleaned off oil sump before removing oil plug. 2. Keep blower clean, especially the engine and engine air filter. 3. Check all nuts, bolts and screws occasionally to be sure blower is in good operating condition. 4. The wheel bearings are pre-lubricated at the factory and should require no further attention until blower is serviced. However, it is advisable to remove the wheels and apply a small amount of light oil to each axle at least once a season. OFF-SEASON STORAGE If you are going to store your blower for any length of time (30 days or longer), it is important that the following steps be taken: 1. Drain the gas tank. Start the engine. Allow it to run out of gas. Gasoline left in the engine will leave gum deposits in the carburetor and gas tank. 2. Clean engine of all foreign matter. 3. Lubricate cylinder by removing the spark plug and pour in one ounce of clean lubricating oil through the spark plug hole into the cylinder. Crank engine slowly to spread oil and replace spark plug. To start after storage, remove spark plug and rotate engine with starter to remove excess oil. A CAUTION FIGURE 7. When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially springs and bearings. 6 NOTES Models 692, 693, 694 and 24695 i 8 Models 692, 693, 694 and 24695 PARTS LIST FOR LEAF BLOWER MODELS 692, 693, 694 and 24695 Ref. No. Part No. Color Code Description New Part 1 749-0479 Upper Handle 5 714-0114 Sq. Key 1/4" x 1/4" x 2.00" Lg.* 6 710-0442 Hex Bolt 5/16-18 x 1.50" Lg.* 7 14526- - 488 Engine Mounting Frame Ass'y. 8 736-0119 L.-Wash. 5/16" I.D.* 9 712-0267 Hex Nut 5/16-18 Thd.* 10 736-0187 FI.-Wash. .63" I.D. x 1.25" O.D. 11 1544-009 Cotter Pin 5/32" Dia. x 1.25" Lg.* 12 712-0206 Hex Nut 1/2-13 Thd.* 13 736-0921 L.-Wash. 1/2" I.D.* 14 734-1036 Swivel Caster Wheel 5" Dia. x 1.25" 15 14571 - 488 Caster Arm Ass'y. 16 710-0726 Hex Wash. Hd. "AB" Tap Scr. 5/16" x .75" Lg. 17 14529 -488 Caster Arm Bracket 19 734-1035 Wheel Ass'y- Comp. 12" x 3" (692, 693 & 694) (I net. Ball Bearings) 734-1044 Wheel Ass'y- Comp. 11" x 4" (24695 Only) 741-0313 Bearings (24695 Oniy) 20 736-0159 FI.-Wash. 34" I.D. x .87" O.D. 21 710-0170 Hex Locking Bolt 5/16-24 x .62" Lg. 22 736-0162 FI.-Wash. 23 712-0267 Hex Nut 5/16-18 Thd.* 24 736-0119 L.-...

Herunterladen

Geben Sie zwei Ziffern: