Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Snapper Dateigröße: 327.76 kb Dateiname: Unterrichtssprache:

Hinge & Deflector (Deflector Removed for Clarity) D. Tapered Spacer E. Original Lockwasher and Nut F. 5/8 x 1 Cylinder Spacer A BC Figure 7. Connect Deflector Spring A. Spring Anchor B. Spring C. Deflector Arm 6 7 54”Turbo Blower Installation Instructions FRONT Install Turbo Blower 1. Install the turbo blower assembly. Insert the tapered spacers (B, Figure 8) through the bottom of the blower housing (A). 2. Install one spring clip (C) on both tapered spacers (B). 3. Hook the bottom of the turbo on the bottom hook bracket. 4. Use the release lever to release tension on the belt, and install the belt on the new arbor pulley (see Figure 9). 5. Rotate the belt cover into position and secure with the plastic knob (D, Figure 8). 6. If not already done, install the bracket (E) using the existing capscrew. 7. Install the spring (F). Connect the top of the spring to the bracket (E) and the bottom to the hole in the mower deck shell, just behind the discharge opening. Install Baffles 1. Remove and discard the existing baffle from the left side of the mower. It is replaced by turbo baffles. 2. Install the left (23-1/2” long) baffle and right (26-1/2”) front baffle (B & C, Figure 10) using six 5/16-18 x 3/4 carriage bolts (A), lockwashers, and nuts (D). Be sure the bolts are inserted fully into the slots in the mower deck. Figure 8. Install Turbo A. Turbo Blower Assy. D. Plastic Knob B. Tapered Spacers E. Bracket C. Spring Clips F. Spring A E F B C C B D Figure 9. Belt Routing Figure 10. Install Front Baffles A. 5/16-18 x 3/4 Carriage Bolts B. Left Front Baffle (23-1/2” Long) C. Right Front Baffle (26-1/2” Long) D. 5/16-18 Nut and Lockwasher C B D D A A Installation Instructions 54”Turbo Blower E F C NORMAL INSTALLATION AND REMOVAL Installation 1. Insert the tapered spacers (B, Figure 11) through the bottom of the blower housing (A). 2. Install one spring clip (C) on each of tapered spacers (B). A 3. Hook the bottom of the turbo on the bottom hook bracket. 4. Use the release lever to release tension on the belt, and install the belt on the arbor pulley (see Figure 12). 5. Rotate the belt cover into position and secure with the plastic knob (D, Figure 11). B C B D 6. Install the spring (F). Connect the top of the spring to the bracket (E) and the bottom to the hole in the mower deck shell, just behind the discharge opening. Figure 11. Install Turbo A. Turbo Blower Assy. WARNING B. Tapered Spacers C. Spring Clips The deflector must be properly installed in the D. Plastic Knob down position and retained by the spring. Do not E. Bracket operate the unit without a deflector. F. Spring Removal 1. Remove the spring (F, Figure 11). 2. Loosen the plastic knob (D, Figure 11). 3. Use the release lever to release tension on the belt, and remove the belt from the arbor pulley (Figure 12). 4. Remove the spring clips (C, Figure 11) from the tapered spacers (B). 5. Remove the turbo assembly (A) from the deck. 6. Close the small belt cover and secure with the plastic knob (D, Figure 11). 7. Return the deflector to the down position. NOTE: The baffles (Figure 10) do not need to be removed. FRONT Figure 12. Install Turbo MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA Form No. 1720927-06 Rev. 03/2007 © 2007 Briggs and Stratton, Inc. Al...

Herunterladen

Geben Sie zwei Ziffern: