Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Stihl Dateigröße: 1.04 mb Dateiname: Unterrichtssprache:

Fotos und technische Daten  Stihl  BGE 71

N Push the elbow (5) into the fan housing stub (6) as far as stop. N Push the union nut (7) over the fan housing stub (6) and turn it in the direction of the arrow as far as the stop. You will hear the safety switch being activated. Assembling the Suction Tube 295BA080 KN NLine up the arrows on the suction tube and extension tube. Push together and lock in position. BGE 61, BGE 71 BGE 61, BGE 71 English 10 Mounting the Suction Tube N Shut off the engine. N Press tab (1) towards fan housing, rotate intake screen (2) in direction of arrow as far as the stop, and lift it away. N Line up the arrows (3). N Push the suction tube into the intake opening as far as the stop. N Push the union nut (4) over the intake opening. N Line up the arrows (3 and 5). N Rotate the union nut (4) in direction of arrow until the lever (6) engages audibly on the fan housing. Removing the Elbow N Shut off the engine. N Rotate the union nut (1) in the direction of the arrow as far as the stop. N Remove the elbow (2). Removing the Suction Tube N Switch offf the motor. N Operate the lever (1), rotate the union nut (2) in direction of arrow as far as the stop and remove together with the suction tube. N Position the intake screen (3) on the intake opening. N Line up the arrows (4). N Rotate the intake screen nut (3) in direction of arrow until the lever (5) engages audibly on the fan housing. 1 290BA018 KN 290BA009 KN 290BA008 KN 5 1 290BA011 KN 290BA010 KN 5 4 290BA017 KN Connecting to Power Supply Make sure your cord set is in good condition. When using an extension cord set, be sure to use one heavy enough to carry the current your product will draw. An undersized extension cord set will cause a drop in line voltage resulting in English Strain Relief Switching On To reduce the risk of disconnection of the power supply cord from the N Make sure you have a secure and extension cord set during operation: balanced footing. N Hold the unit in the normal working position. NMake a loop in the extension cord. NPass the loop (3) through the 4290BA013 KN 35 1 290BA016 KN loss of power and overheating. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Minimum wire gauge for extension cords for 120 Volt appilances using 6 - 10 Amps (Cord types SJW or SJTW): N Move switch (1) to I or II (position II opening (4). depends on model). Cord length (ft) Wire gage (AWG) N Slip the loop over the hook (5) and Units with single switch setting (I): 50 16 pull it tight. 100 14 N Connect the extension cord plug to I = full power a properly installed power outlet. 150 12 Units with two switch settings (I and II): Appropriate extension cords are I = half power available in special stores for electrical II = full power equipment or from your STIHL dealer. 21 290BA012 KN N Insert the appliance plug (1) into extension cord coupling (2). BGE 61, BGE 71 English Switching Off During longer work breaks – disconnect the plug from the power supply. When the machine is not in use, shut it off so that it does not endanger others. Secure it against unauthorized use. Storing the Machine N Thoroughly clean the machine. N Store the machine in a dry, high or locked location, out of the reach of children and other unauthorized persons. 1290BA016 KN N Move the switch (1) to 0 BGE 61, BGE 71 English Maintenance and Care The following intervals apply to normal operating conditions only. If your daily working time is longer or operating conditions are difficult (very dusty work area, etc.), shorten the specified intervals accordingly. before starting workafter finishing work or dailyweeklymonthlyyearlyif problemif damagedif required Complete machine Visual inspection (condition) x Clean x Control handle Check operation x Cooling inlets Clean x Safety labels Replace x BGE 61, BGE 71 English Main Parts 1 2 3 4 5 6 7 8 9 10 11 12 # 94# 651290BA019 KN 27810111233 Nozzle Blower tube Union nut (for fan housing stub) Switch Handle Strain relief Power supply cord Intake screen (for intake opening) Union nut with handle* Suction tube* Elbow* Catcher bag* Serial number * special accessory for BGE BGE 61, BGE 71 English Definitions 12 Catcher bag*. Mounts to elbow to collect the 1 Nozzle. vacuumed debris. Aims and widens the airstream. # Serial number 2 Blower tube. Directs airstream. 3 Union nut. Secures blower tube to fan housing stub. 4 Switch. To switch the machine in position "ON" and "OFF". 5 Handle. For control of machine during blowing operation work. 6 Strain relief. Supports extension cord and reduces the likelihood of unintentional disconnection of extension cord and power supply plug. 7 Power supply cord. Supplies electricity to the appliance. 8 Intake screen. Fits over the intake opening and reduces the risk of direct contact with the fan wheel, which is located under the screen. 9 Union nut with handle*. Attaches suction tube to the intake...

Herunterladen

Geben Sie zwei Ziffern: