Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Craftsman Dateigröße: 437.85 kb Dateiname: Unterrichtssprache:

thatmayreduce This product is listed by Underwriters Laboratories, Inc. in accordance with UL Standard 1017. If situations occur which are not cov ered in this manual, use care and good judgement. If you need assistance, contact your Sears Service Center or call 1-800-235-5878. Failure to follow all Safety Rules and Precautions can result in serious injury. SAVE THESE INSTRUCTIONS CARTON CONTENTS Model 358.798370 Blower Blower Tube Nozzle 2 Vacuum Tubes Collection Bag Examine parts for damage. Do not use damaged parts. NOTE: If you need assistance or find parts missing or damaged, call the 1-800 number found on the front page of this manual. ASSEMBLY WARNING: If received repeat all steps to ensure properly assembled and are secure. assembled, your unit is all fasteners ASSEMBLY INSTRUCTIONS FOR USING YOUR UNIT AS A BLOWER NOTE: Assembly instructions for using your unit as a vacuum follow this section. ATTACHING THE BLOWER TUBE AND NOZZLE If you have already assembled your unit for use as a vacuum, remove the vacuum tubes and • Insert the blower outlet. • Twist the blower it is firmly seated • Twist the nozzle blower tube until the collection tube into the tube clockwise in the blower bag. blower until outlet. into the end of the it is firmly seated. Make sure the nozzle points upward. Blower Outlet _...._._,_,_._% \ / Blower Tube Blower Tube Nozzle ASSEMBLY INSTRUCTIONS FOR USING YOUR UNIT AS A VACUUM NOTE: Assembly instructions for using your unit as a blower is explained in the previous section. WARNING: Stop the unit and disconnect from the power source before opening the inlet cover or attempting to insert or remove the inlet restrictor or vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. NOTE: If you have already assembled your unit for use as a blower, remove the blower tube and nozzle. REMOVE THE INLET RESTRICTOR An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use, and must be removed during assembly for vacu um use. NOTE: Be sure to keep the inlet restrictor for using your unit as a blower. • Open the inlet cover by inserting the tip of a screwdriver into the inlet cover latch area, and twisting the screwdriver while pulling the inlet cover open. Bottom view of unit • Rotate the inlet restrictor counterclockwise, and lift out of the unit. Do not close the inlet door. You will next attach the vacuum tubes. ATTACHING THE VACUUM TUBES There are 2 vacuum tubes, an upper and lower tube. The upper tube is cut straight on both ends, and attaches to the blower unit. The second tube is cut an at angle on the lower end. This angled end will point toward the ground during vacuum use. • Locate the arrows on the upper vacuum tube and on the vacuum inlet area of the unit. Upper Vacuum Tube • While holding the inlet cover open, align the arrows and insert the vacuum tube into the opening. Twist the tube clockwise until it is seated. A second arrow on the vacuum tube will align with the arrow on the unit once the tube twisted completely in place. Align arrows on tube & unit • Attach the lower vacuum tube to the upper vacuum tube by aligning the arrows on the two tubes. Press the tubes together until the lower tube is fully seated in the upper tube. (About 3 inches) Upper Lower ATTACH THE COLLECTION BAG Slide the opening of the collection bag over the blower outlet. Pull the strap with velcro tightly through the buckle and secure with velcro tabs. NOTE: Make sure the strap with velcro is located on the blower outlet as shown. Also, make sure the zipper on the bag is completely closed. Stra_ Collection _ _ _T.._ Bag _ Blower Outlet ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG • Carefully loop the shoulder strap through the buckle as shown in the illustration below. Last In First In • Position the unit on your right-hand side, blower outlet and bag pointing toward the rear. Hold the unit in an upright position, and support the lower vacuum tube on the ground. • Place the shoulder strap over your head and onto your left shoulder. • Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not oper ate properly. NOTE: The strap is designed to position the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit. Shoulder strap on left shoulder No kinks in bag Allows free air flow HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE. • Stop unit and unplug the extension cord. • Remove the vacuum tubes and collection bag. • Install the inlet restrictor that was removed when assembling for vacuum use. NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. This restrictor improves the blower function. • Close the inlet cover and make sure it is latched closed. • Re-install the blower tubes. Refer to the section ATTACHING THE BLOWER TUBE AND NOZZLE for instr...

Herunterladen

Geben Sie zwei Ziffern: