Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
See Figure 5. Snap switch Bracket Tabs Figure 5 Step 4. While holding the snap switch bracket against the pedestal, slide the bracket towards the rear of the stove until it comes to a stop. Once the snap switch bracket is in place you can then remove the flat head screwdriveror pry bar that was used to create theopening between the firebox bottom and pedestal. See Figure 6. Snap switch housing Figure 6 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 5. With the snap switch bracket in place, using a 9/16” wrench or Step 5. With the snap switch bracket in place, using a 9/16” wrench or Install the control box by sliding the front control box slot over the socket wrench you can now tighten down both left and right side 3/8” bolt head from Step 6. Slide control box towards the center pedestal bolts. See Figure 7. of the stove until it stops on the tabs. See Figure 10. Tighten Left and Right Pedestal Bolts Figure 7 Step 6. Locate the 3/8” diameter x 1/2” long bolt on the bottom of the firebox near the draft handle. Using a 9/16” wrench or socket loosen this bolt but do not remove from threaded hole. See Figure 8. Note: This bolt was holding the stoves shipping legs on the stove and should have been reinstalled with the other three bolts that were holding the shipping legs on the stove per the pedestal instructions. Bolt Draft handle Figure 8 Step 7. Locate front slot on the Control Box as shown in Figure 9. Slot Tabs Figure 10 Step 9. Using a 9/16” open end wrench tighten down the 3/8” bolt holding the control box. See Figure 11. Figure 11 Step 0. Connect the wire harness from blower to female connector on rear of snap switch bracket. See Figure 12. Figure 12 Figure 9 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step .Visually inspect wires are clear of contact with bottom of firebox. See Figures 11 through 13. Step .Visually inspect wires are clear of contact with bottom of firebox. See Figures 11 through 13. Step 2. Plug the power cord into a grounded 120 VAC receptacle. Do not route the power cord under the stove or allow it to come in contact with any surface of the stove. WOODSTOVES WITh LEG BASE Step . Using a 9/16” wrench or socket loosen the left heat shield bolt. This bolt is located on the bottom side of the leg heatshield as Snap Switch harness Figure 13 Snap Switch Bracket heat Shield Snap Switch Bracket shown. See Figure 14. Left heat Shield Bolt Figure 14 Step 2.Insert snap switch bracket between the heatshield and the bottom of firebox making sure entire assembly is on the left side of the heatshield bolt. Slide back until the notch on the bottom front of the bracket falls into the lip on the front of the heatshield, and as- sembly is parallel with side of firebox. See Figures 15 and 16. Figure 16 Step 3. Locate the tabs on the back of the control box. Slide the tabs onto the upper edge of the left side of the heatshield. See Figures 17 and 18. Upper Edge Of The Left Side heatshield Figure 17 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Tabs Control Box Tabs Control Box Step 4. Usinga9/16”wrench,slowlystarttotightenthebottomheatshield bolt. While tightening bolt, and before snug, make sure the snap switch housing does not shift. DO NOT OVERTIGhTEN. Make sure snap switch is making firm, flat contact with ashlip, and does not shift. See Figure 19. Snap Switch Snap Switch Figure 19 Step 5. Plug the blower harness into plug on rear of snap switch bracket. See Figure 20. Blower Wire harness Snap Switch Bracket Figure 20 Step 6. Visually inspect wires are clear of contact with firebox. See Figures 20 through 21. Snap Switch harness Bottom of Firebox Figure 21 Step 7. Plug the power cord into grounded 120 VAC receptacle. Do not route the power cord under the stove or allow it to come in contact with any surface of the stove. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. The blower can be operated manually or automatically (blower will turn on when the stove is hot and turn off when the stove is cool). The rocker switch on the control panel allows you to select between manual operation or automatic operation as follows (see Figure 23): MANUAL OPERATION: Turn rocker switch to the “MANUAL” position and adjust rheostat knob to the desired speed. The blower will have to be manually turned “OFF” by rotating the rheostat knob counterclockwise until it clicks. AUTO OPERATION: Turn rocker switch to the “AUTO” position and the rheostat to the ON position (rotate rheostat knob clockwise until it clicks). When the stove warms up, the blower will automatically turn on (adjust rheostat knob to the desired speed setting). When the stove cools down, the blower will automatically turn off. Rheostat Operation -The highest blower speed is obtained by turning the rheostat knob clockwise until it clicks “ON”, then rotate towards “HIGH” to increase blower speed. Rotate the knob clockwise for a lower speed. To turn off, continue to rotate the knob counterclockwise until it clicks “OFF.” Blower Operation Guidel...