Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Shindaiwa Dateigröße: 668.1 kb Dateiname: Unterrichtssprache:

n Use medium to higher throttle settings to move grass or leaves from parking lots or walkways. n Use full throttle when moving heavy loads such as dirt or snow. IMPORTANT! Blower noise increases at higher throttle settings! Always use the lowest throttle setting required to get the job done! Wear eye protection that meets ANSI Z87.1 such as a face shield or goggles while operating this machine! Wear close-fitting clothing to protect your legs and arms, and Do not wear clothing or jewelry that could get caught in machinery! Secure hair so that it is above shoulder length! 48011B Wear hearing protection when operating the blower. Wear a dust mask to reduce the risk of inhalation injuries. Always be aware of the strength and direction of the blower discharge stream! Never direct the blower discharge stream toward people or animals! Never operate the blower if any component parts are damaged, loose, or missing! Never operate the blower when visibility is poor. Figure 11 12 EVERY 10 HOURS ROUTINE MAINTENANCE IMPORTANT! Maintenance, replacement or repair of emission control devices and systems may be performed by any repair establishment or individual. However, warranty repairs must be performed by a dealer or service center authorized by Shindaiwa Corporation The use of parts that are not equivalent in performance and durability to authorized parts may impair the effectiveness of the emission control system and may have a bearing on the outcome of a warranty claim. (more frequently in dusty conditions) Remove the Element Cover Latch 48013 Element Cover Snap the cover up from the bottom to remove. Figure 12 WARNING! Before performing any maintenance on this blower, stop the engine and disconnect the spark plug wire! 1. Remove the air cleaner cover by gently lifting the cover latch. See figure 12. 2. Inspect the filter. If the element is damaged or distorted, replace it with a new one. IMPORTANT! The EB501 uses a special high capacity dry-type air filter element. The filter should not be cleaned with a liquid cleaner and must NEVER be oiled! 3. Tap filter gently on a hard surface to disloge debris from element or use compressed air to blow debris from the air filter element. IMPORTANT! Direct the air stream at the inside face of the filter only! 4. Wash the filter cover with soap and water and blow dry. 5. Install the filter element and cover in the reverse order of removal. Daily Maintenance n Remove dirt and debris from the blower exterior. n Inspect the engine, tank, and hoses for possible fuel leaks, and repair as necessary. n Inspect the entire blower for loose, damaged, or missing components, and repair as necessary. n Inspect the engine cooling fins for accumulations of dirt or debris, and clean as necessary. CAUTION! Dirty or damaged cooling system components may allow the engine to overheat, possibly causing serious engine damage! Operating the blower with loose, missing, or damaged components could allow the engine to overspeed, possibly causing serious engine damage! CAUTION! Never operate the blower if the air cleaner assembly is damaged or missing! 13 EVERY 10/15 HOURS EVERY 50 HOURS 48017 (more frequently if reduced performance is noted) to remove n INSPECTION Inspect the entire blower and tubes for damage, including loose or missing components, and repair as necessary. n SPARK PLUG Replace the spark plug with a Champion CJ8 or equivalent, gapped to 0.024 inch (0.6mm). FUEL FILTER Use a bent piece of wire to extract the fuel filter from inside the fuel tank, and then remove and replace with a new element. See figure 14. CAUTION! Do not nick or perforate fuel tube with wire hook! Before reinstalling the filter, inspect the condition of the fuel line. If damage or deterioration are noted, the blower should be removed from service until it can be inspected by a Shindaiwa-trained service technician. n COOLING SYSTEM Use a wood or plastic scraper and a soft brush to remove dirt and debris from the cylinder fins and crankcase. 48015 0.024" (0.6mm) gap Champion CJ8 Spark Plug Wire Hook 48014 Figure 14 1. Use the spark plug wrench to remove the spark plug (turn counter- clockwise to remove). See figure 13. 2. Clean and adjust the spark plug gap to 0.024” (0.6mm). Replace any damaged or visibly worn plug with a Champion CJ8 or equivalent. See figure 13. 3. Install the spark plug finger-tight in the cylinder head, then tighten it firmly with the spark plug wrench. Avoid overtightening. Fuel Filter Fuel Tank Figure 14 CAUTION! Never allow dirt or debris to enter the cylinder bore! Before removing the spark plug, thoroughly clean the spark plug and cylinder head area! Allow the engine to cool before servicing the spark plug! Cylinder threads can be damaged by tightening or loosening the spark plug while the engine is hot! 14 135-HOUR MAINTENANCE Every 135 hours of operation, remove and clean the muffler. Muffler Body 48016D First, remove the spark plug Remove the Engine Cover Muffler Screw Retaining Tab Engine ...

Herunterladen

Geben Sie zwei Ziffern: