Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Move away from the area of the spill and avoid creating any source of ignition until fuel vapors have dissipated. OPERATIONAL SAFETY 1. Carefully read and follow all caution stickers. 2. Operate only in daylight or good artificial light. 3. Do not operate machine unless all guards, shields and covers are in place and in proper working condition. 4. It is essential all operator safety mechanisms be connected and in operating condition prior to use. 5. Do not change the engine governor settings or over-speed the engine. Operating an engine at excessive speed may increase the hazard of personal injury. 6. Disengage all blade and drive clutches (release bail) before starting. 7. Start the engine carefully with feet well away from the blades. 8. Do not put hands, feet or clothing near rotating parts while the unit is being operated. 9. Travel up and down slopes at a 45° angle rather than across, to prevent unit from tipping over. 10. Exercise extreme caution when changing direction on slopes. Do not get too close to sharp drop-offs or operate unit on excessively steep slopes. 11. Use caution when backing up or pulling the unit towards you. 12. Stop the blades if unit has to be tilted for transportation, when crossing surfaces (i.e. sidewalks, driveways, stepping stones, etc.) or when transporting the unit to and from the area being worked on. 13. Never pick up or carry a TRS-20/TSS-20 while the engine is running. 14. Stop the engine and disconnect the spark plug wire: a) before checking, cleaning or working on unit b) after striking a foreign object (inspect the unit for damage and make repairs before restarting and operating) 15. Stop the engine: a) whenever you leave the unit b) before refueling c) before clearing blockages. 16. Reduce the throttle setting during engine run-out and, if the engine is provided with shut-off valve, turn the fuel off at the conclusion of operating. 17. Before shutting off, put drive lever in neutral. OPERATION PREPARATION 1. Carefully read this manual and operate TRS-20/TSS-20 correctly. 2. Always check machine on level ground. 3. Visually check all moving parts and all fasteners, if loose or broken, tighten or replace. Check for broken or bent blades, replace if necessary. 4. Lubricate all fittings after every four hours of using machine, using a pressurized gun with standard lithium base lubricant (see “General Maintenance” section). Wipe off fittings before and after lubricating. 5. Add oil to the engine crankcase with engine resting in a level position (refer to engine manufacturer’s Owner’s Manual for the correct type and amount of oil). 6. Fill the fuel tank according to engine manufacturer specifications. 7. Police lawn area for obstacles and debris (i.e. sprinklers, hoses, toys, etc.) 8. Mark underground sprinkler heads and other hidden obstacles to prevent damage. STARTING ENGINE CAUTION TO AVOID INJURY, DO NOT PLACE YOUR FEET OR OTHER BODY PARTS UNDER THE BLADES WHILE STARTING THE ENGINE. 1. Turn fuel cock to the “open” position 2. Turn choke on (closed). 3. Turn ignition switch to “on”. 4. Move throttle control to high RPM setting. Do not exceed 3600 rpm. 5. Pull recoil starter rope until engine starts. 6. After engine is warm, turn off choke (open). 7. Allow engine to run one minute before operating. 8. Check engine rpm setting before operating, DO NOT exceed 3600 rpm. TRANSPORTING THE TRS-20/ TSS-20 Fig. 1 Fig. 2 1. Position height adjustment lever to the start/transport position (see Fig. 1). 2. Start Engine, drive up ramps, make sure the blades do not hit the ramps or vehicle. 3. Slow the throttle to desired speed for loading. 4. To clear sidewalks, driveways, etc., press down on handle, raising front of the TRS-20/TSS-20. OPERATING THE TRS-20/TSS-20 1. Put speed lever in neutral position. 2. Start engine. 3. Engage bail. 4. Move speed lever forward, to move forward. 5. Move speed lever backwards, to reverse. 6. Drive TRS-20/TSS-20 to area to be raked or seeder. 7. Move height adjustment lever to the appropriate setting for the shaft assembly being used. (see “Optional Shaft Assemblies” section) 8. Lift bail to engage the main shaft. Release bail to stop. OPTIONAL BLADE ASSEMBLIES CHANGING BLADE ASSEMBLIES Within minutes your machine can be converted to a turf rake, turf seeder or turf slicer by purchasing the optional blade assemblies available complete with side plates, bearings and drive pulley. Changing the blade assembly can be done quickly as described below. Fig. 3 1. Set unit up on block allowing enough distance beneath machine to change blade assembly. 2. After removing the belt shield, remove the twelve bolts on the left side and three on the right side which hold the blade assembly to the main body (see Fig. 3). 3. Remove the belts from both sides and remove the entire blade assembly. There is no need to loosen any set screws. 4. Next install the optional blade assembly and fasten with six 1/4” x 5/8” bolts on each side. Tighten all bolts on both shields....
Dieses Handbuch ist für folgende Modelle:Lüftungs - TSS-20 (1.36 mb)
Lüftungs - TRS-20 (1.36 mb)
Lüftungs - TSS-20 (1.36 mb)