Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Failure to follow these plug disconnected. Keep vents and dis-requirements is a violation of the law. This unit charge tubes free of debris which can ac-is not factory equipped with a spark arresting cumulate and restrict proper air flow. screen; however, a spark arresting screen is D Never place any object in the air intake available as an optional part. If a spark arrest- opening as this could restrict proper air flow ing screen is required in your area, contact and cause damage to the unit. your authorized service dealer for the correct D Never use for spreading chemicals, fertil-kit. The spark arresting screen, blower tubes, izers, or other substances which may con-and nozzles must be assembled to unit to be tain toxic materials. in full compliance with regulations. --4 - - ASSEMBLYASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or accessing movable parts. WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit. D A standard screwdriver is required for assembly. BLOWER TUBE ASSEMBLY 1. Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place. NOTE: Knob must be loose enough to allow blower tube to be inserted in blower outlet. Loosenknobbyturningcounterclockwise. BlowerTubeBlowerOutletRibGroove2.Securethetubebyturningtheknobclockwise. 3. To remove the tube, turn the knob counterclockwise to loosen the tube; remove the tube. VACUUM BAG ASSEMBLY 1. Open the zipper on the vacuum bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. SmallOpeningZipperOpeningElbowTubeRib NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom. 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Remove blower tube from engine. --5 - -- Groove Rib 5. Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove. 6. Turn knob clockwise to secure elbow tube. VACUUM TUBE ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. 1. Align the lower vacuum tube as shown. Push lower vacuum tube into upper vacuum tube. LowerVacuumTubeUpperVacuumTube 2.Insertthetipofascrewdriverintothelatchareaofthevacuuminlet. LatchAreaBlowerOutletVacuumInletCoverLatchArea 3. Gently tilt the handle of the screwdriver toward the back of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. 4. Hold the vacuum inlet cover open until upper vacuum tube is installed. VacuumInlet Retaining Post Vacuum Inlet Cover 5. Place the hooks of the upper vacuum tube on the retaining posts of the unit. 6. Pivot the tube until it is secured to the blower unit by the vacuum inlet latch. RetainingPostHookInletCoverLatchPIVOT HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area of the vacuum inlet. 2. Gently tilt handle of screwdriver toward the back of the unit to release the latch while pulling up on the upper vacuum tube with your other hand. LatchArea 3. Remove the vacuum bag. 4. Close the vacuum inlet cover and make sure it is latched closed. 5. Reinstall the blower tube (see BLOWER TUBE ASSEMBLY). SHOULDER STRAP ADJUSTMENT 1 Hold the unit as shown with the muffler side facing away from your body and clothes. 2. Pass the shoulder strap over your head and onto your right shoulder. 3. Extend your left arm toward the rear of the vacuum bag. 4. Adjust shoulder strap until the vacuum bag/shoulder strap seam lies between your thumb and index finger. 5. Make sure air flows freely from the elbow tube into bag. If bag is kinked, the unit will not operate properly. --6 - - OPERATIONOPERATION KNOW YOUR BLOWER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. ChokeLeverFuelMixFillCapStarterRopeThrottleLeverSparkPlugBlowerTubePrimerButtonRearHandleLowerVacuumTubeUpperVacuumTubeVacuumBagElbowTube THROTTLE LEVER The THROTTLE LEVER is used to select the desired engine speed and to stop the engine. Move the throttle lever to the position for full speed operation. Move the throttle lever to the position for idle speed. To stop the engine, move the throttle lever to the STOP position. PRIMER ...