Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
If you need assistance, contact your authorized service dealer or call 1-800-554-6723. Failure to follow all Safety Rules and Precautions can result in serious injury. SAVE THESE INSTRUCTIONS ASSEMBLY WARNING: Stop the unit and disconnect from the power source before opening the inlet cover or attempting to insert or remove the inlet restrictor, blower tube, nozzle, or vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. 4 WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on unit. S A standard screwdriver is required for assembly. BLOWER ASSEMBLY NOTE: Assembly intructions for using your unit as a vacuum follow this section. ATTACHING THE BLOWER TUBE AND NOZZLE 1. Insert the blower tube into the blower outlet. 2. Twist the blower tube clockwise until it is firmly seated in the blower outlet. 3. Twist the nozzle into the end of the blower tube until it is firmly seated. Make sure the nozzle points upward. BlowerTubeNozzleBloweroutlet For Model 2695 only, the blower extension tube and nozzle are combined into one component. Blower Tube/Nozzle VACUUM ASSEMBLY (Some models) NOTE: Assembly instructions for using your unit as a blower are explained in the previous section. If you have already assembled your unit for use as a blower, remove the blower tube and nozzle. REMOVE THE INLET RESTRICTOR An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use and must be removed during assembly for vacuum use. NOTE: Be sure to keep the inlet restrictor for using your unit as a blower. 1. Ensure unit is stopped and extension cord is unplugged. 2. Open the inlet cover by inserting the tip of a screwdriver into the latch area on the vacuum inlet cover. Gently tilt handle of screwdriver toward the front of the unit while pulling up on the vacuum inlet cover with your other hand. ImpellerLatchAreaVacuumInletCover 5 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. Vacuum Inlet Cover Inlet Restrictor ATTACHING THE VACUUM TUBES There are 2 vacuum tubes, an upper and lower tube. The upper tube is cut straight on both ends and attaches to the blower unit. The lower tube attaches to the upper tube, and has an angled end that you point toward the ground during vacuum use. 1. Ensure unit is stopped and extension cord is unplugged. 2. Locate the arrows on the upper vacuum tube and on the vacuum inlet area of the unit. Upper Vacuum Tube 3. While holding the inlet cover open, align the arrows and insert the vacuum tube into the opening. Twist the tube clockwise until it is seated. A second arrow on the vacuum tube will align with the arrow on the unit once the tube is twisted completely into place. Alignarrowsontubeandunit 4. To attach the lower vacuum tube to the upper vacuum tube, first align the arrows on the two tubes. Then, press the two tubes together until the lower tube is securely seated in the upper tube (about 3 inches). UpperTubeLowerTube ATTACH THE COLLECTION BAG Slide the opening of the collection bag over the blower outlet. Pull the velcro strap tightly through the buckle and secure to the velcro tabs. NOTE: Make sure the velcro strap is lo-2. Remove the vacuum tubes and cated on the blower outlet as shown be-collection bag. low. Also, make sure the zipper on the 3. Install the inlet restrictor that was re- bag is completely closed. moved when assembling for vacuum VelcroStrapCollectionBagBlowerOutlet ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG 1. Carefully loop the shoulder strap through the buckle as shown in the illustration below. FirstInLastIn 2. Position the unit on your right-hand side, blower outlet and bag pointing toward the rear. Hold the unit in an upright position with the lower vacuum tube on the ground to support it. 3. Place the shoulder strap over your head and onto your left shoulder. 4. Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not operate properly. NOTE: The strap is designed to position the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit. Shoulder strap on left shoulder No kinks in bag allows free air flow HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Stop unit and unplug the extension cord. 6 use. NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. This re strictor improves the blower function. 4. Close the inlet cover and make sure it is latched closed. 5. Re-install the blower tubes. Refer to the section ATTACHING THE BLOWER TUBE AND NOZZLE for instructions on how to attach these items. SELECT AN EXTENSION CORD Use only a 120 A.C. voltage supply as shown on the nameplate of the uni...