Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• Specifications are subject to change without notice. English 14 .. SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. NOTE A light lubricant may be used to ease assembly of flexible hose to blower elbow. .. THROTTLE LEVER [330BT/350BT/370BTS/380BTS] 1. Set up the throttle holder to the swivel and tighten the screw on the holder. When setting up the holder, please make sure to match the holder to the convex on the swivel joint as shown in F2. 2. Adjust the position and angle to achieve a comfortable working position, and tighten the throttle lever. (1) Cable (2) Hose .. THROTTLE CABLE [330BT/350BT/370BTS/380BTS] [330BT] • Fasten the throttle cable at central position of the hose by the band attached to the throttle cable. First, wrap the hose with the band fixed to the throttle cable from the lower side. Then, pass the band through a hole of the band as shown in figure. Please note that there is a possibility of damaging the hose if the band is fastened too tightly. [350BT] [370BTS] [380BTS] • Use the clamp to fasten the colgate tube containing the throttle cable and the power cable to the hose. (1) Clamp .. RIGHT HANDLE [350BF/370BFS/380BFS] • Insert the handle holder to the swivel and tighten the screw on the holder. When setting up the holder, please make sure to match the holder to the convex on the swivel joint as shown in F5. .. HANDLEBAR [OPTION] [330BT/350BT/370BTS/ 380BTS] 1. Insert the holder, then assemble the handlebar (OPTION) and tighten it securely. F1 (1) (2) F2 F3 [330BT] (1) F4 [350BT] [370BTS] [380BTS] F5 F6 Assembly English 15 .. BLOWER TUBES 1. Align the protrusion and the groove provided on the tube ends and twist the tube until the connection is locked. NOTE A light lubricant may be used to ease assembly of blower tube. NOTE If longer tube is required, the second straight pipe can be connected with the first one. If higher air speed is required, the round blow pipe can be replaced by the flat nozzle with the second straight pipe. (1) Flat nozzle (option) .. HARNESS NOTE The harness must always be worn when working with the machine. Failure to do so means you will be unable to maneuver safely and this can result in injury to yourself or others. A correctly adjusted harness and machine significantly facilitates the work. Adjust the harness to give the best working position. Tighten the side straps so that the pressure is evenly distributed across the shoulders. .. WAIST BELT [350BT/BF][370BTS/BFS][380BTS/BFS] • The waist belt is attached to the rings on the left and right sides of the frame. NOTE 330BT has no waist belt. Place the waist belt around your waist and not too far down on the stomach. Tighten the waist belt strap so that you feel the weight of the blower resting on your hip. • Be sure to always tighten the buckle in front of your body. WARNING • If you are not using a waist belt, be sure to remove it from the unit and store it. • There is a risk that the belt will be caught, toppling the unit. • There is a danger that the belt will be sucked into the fan. F7 F8 (1) F9 F10 F11 F12 F13 Assembly English 16 .. FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10ft (3m) away from the fueling point before starting the engine. • The engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Husqvarna oil is not available, use an antioxidant added quality oil expressly labeled for aircooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) • Do not use BIA or TCW (2- stroke water-cooling type) mixed oil. RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components (i.e., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion. • These engines are certified to operate on unleaded gasoline. • Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL) • If you use a gasoline of a lower octane value than specified, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur. • Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment. • Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine. .. HOW TO MIX FUEL IMPORTANT Pay attention to agitation. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. 3. Pour in all of the oil and agitate well. 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be diffic...
Dieses Handbuch ist für folgende Modelle:Lüftungs - 370BTS/BFS (5.37 mb)
Lüftungs - 380BTS/BFS (5.37 mb)