Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
• The operator is responsible for accidents or hazards occuring to other people or their property. • Do not handle the plug or the tool with wet hands and do not use the tool in the rain. • Use only outdoor rated extension leads that are so marked. Keep the extension cord away from heat, oil and sharp edges. • Ensure that the extension lead is secured in a manner that prevents it form disconnecting from the plug whilst in use. • Keep all the air intakes and the blower tube free of dust, lint, hair and other material that may cause a reduction in air flow. • Keep a balanced and stable stance while using the tool. • Do not switch on the tool in enclosed or poorly ventilated spaces or in the presence of inflammable and/or explosive substances such as liquids, gasses and powders. • Do not get distracted and always concentrate on what you are doing. Use common sense. Never operate the tool when you are tired, sick or under the influence of alcohol or other drugs. • Do not operate this appliance with long loose hair or loose fitting jewellery. Tie long loose hair back and remove loose fitting jewellery. • Do not allow the blower vac to pick up any burning or smoldering materials like ashes, cigarette butts etc. • Do not attempt to pick up breakable objects like glass, plastics, china etc. • Do not use in vaccum operation without the collection bag fitted. • Do not use the blower vac in either the vaccum or the blow position on gravel surfaces. • Only operate the tool during broad daylight or with adequate artificial light. • When the tool is not in use, store it in a dry place and out of reach of children. • After use, disconnect the tool from the power supply and check for damage. If you have the slightest doubts, contact an authorised service centre. • Only use the tool according to the instructions given in this manual. • Check regularly that the screws are tight. • Use only spare parts and accessories recommended by the manufacturer. • Do not try to repair the tool or access internal parts. Contact authorised service centres only. Know your product 1. Lock-off switch 2. Trigger switch 3. Blower/vacuum selector lever 4. Rubber grip handle 5. Auxiliary handle 6. Collection bag 7. Cord support 8. Auxiliary handle adjusting knob 9. Patio head 10. Housing 11. Blow/vac tube 1 2 4 5 10 8 7 3 11 6 9 Unpacking Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Fitting the collection bag Prior to fitting the collection bag, the blow/vac tube must be fitted to the housing. 1. Attach the strap on the collection bag to the hook underneath the blow/vac tube (fig A). 2. Attach the plastic connector to the outlet in the housing, ensuring that the latch at the back ‘clicks’ into position (fig B). To remove the collection bag, disconnect the attachments in the reverse order. Fitting the auxiliary handle For full control of the blower vac the auxiliary handle should always be fitted and adjusted to the most suitable position for the operator. 1. To fit the handle to the housing, fully unscrew and remove the adjusting knob and bolt from the auxiliary handle. 2. Slide the auxiliary handle over the housing, ensuring handle is orientated so as the serrated or pattern surface aligns with the same pattern surface on the housing. 3. Fit the auxiliary locking bolt through the handle and housing from the left hand side of the blower vac (same side as the blower vacuum selector) and tighten in a clockwise direction (fig A). 4. To adjust the angle of the handle, loosen the auxiliary locking knob (rotate in an anti-clockwise direction) and move the handle to the preferred position and then tighten the knob firmly. Fitting the patio head The patio head can be easily fitted or removed from the blow/vac tube. 1. Hold the blower/vac upside down so you are looking down into the blow/vac tube. 2. Ensure the patio head is the correct way up, with the oval indentation facing down. (fig A) 3. Firmly press the patio head into the blow/vac tube till it click’s into position. A A B A 8 Extension cord support During use of the blower vac, the extension cord will continually be pulled as you move from one area to another. An extension cord support has been provided on the housing of the blower vac to assist in preventing the electrical connection between the extension cord and blower vac plug being forced apart. Note. The support is for the extension cord, and not the cable from the blower vac. 1. To fit the extension cord to the support, make a tight loop in the extension cord, approximately 300mm from the socket on the extension cord. 2. Fit the loop into the square recess in the back portion of the blower vac on the underside of the housing (fig A). 3. Push the loop all the way through the housing by approximatel...
Dieses Handbuch ist für folgende Modelle:Lüftungs - ULB2400 (844.61 kb)