Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Use Throttle Position Button to set and hold blower speed for continuous operation. 13. ThROTTLE TRIGGER - Spring-loaded Throttle Trigger controls engine speed. Releasing Trigger returns engine to speed setting set by Throttle Position Stop Switch Button. Always release trigger and allow engine to return to idle before shutting off with Throttle Position Stop Switch Button. Use Throttle Trigger to vary blower speed settings for intermittent operation. 14. BLOWER PIPES -Exclusive positive locking system. 15. FLEXIBLE PIPE -Allows for full range of movement. Power Blower oPerator's Manual Contents ____ 1 - Power Head ____ 1 - Flex Pipe____ 1 - Pipe w/swivel____ 1 - Straight Pipe____ 1 -Straight Pipe w/decal____ 1 - Operator's Manual____ 1 - Warranty Registration Card____ 1 - Plastic Bag ____ 2 - Clamps w/screws ____ 1 - Guide Loop assembly WARNING Never perform maintenance or assembly procedures with engine running or serious personal injury may result. Install blower pIpes 1. Place guide loop (G) across elbow clamp, and turn until clips fully engage clamp band. 2. Assemble clamps (A) onto both ends of flexible pipe (B). NOTE Clamp with cable guide loop (G) fits elbow end of flexible pipe. 3. Assemble swivel pipe (C) into flexible pipe (B). NOTE Assure throttle cable is not twisted before installing handle (E). 4. Position cable between the elbow (D) and frame and along the top of the flexible pipe. Loosen knob (H) on handle (E). Align notch in handle with tabs (F). Install onto swivel pipe (C) past long ridges in pipe. G G BA A E B H F D G C 10 5. Assemble flexible pipe (B) to elbow (D) on blower and tighten clamps (A). Position guide loop (G) on inside (blower side) of flexible tube. NOTE A light lubricant may be used to ease assembly of flexible pipe to blower elbow. 6. Clip throttle cable into throttle cable guide loop (G). 7. Move handle (E) to desired position. Tighten knob (H) hand tight. 8. Assemble straight pipe (I) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection. 9. Assemble straight pipe with decal (J) to straight pipe (I) as in step 8. NOTE Blower use will eventually loosen pipe connections. Exclusive positive locking system allows pipes to be tightened. If loosening occurs, remove two straight pipes and install according to instructions 8 & 9. G E I J C E H operatIon WARNING Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with a spark arrestor and a spark arrestor may be required. The operator should contact local fire agencies for laws or regu- lations relating to fire prevention requirements. fuel NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades and other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving. Wear gloves to protect hands from sharp edges and hot surfaces. Power Blower oPerator's Manual WARNING Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Fuel Requirements Gasoline -Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to inadequate lubrication caused by failure to use anSO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certified oil, such as Echo premium Power Blend X TM, will void the two-stroke engine warranty. IMPORTANT Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals. Handling Fuel DANGER Fuel is VERY flammable. U...