Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Panasonic Dateigröße: 4.07 mb Dateiname: SXPR603.PDF Unterrichtssprache:

(Refer to page 78.) STEP RECORD: Change to the STEP RECORD mode. (Refer to page 80.) PART CLR: Erase all recorded contents of the currently selected part. NOTE CLR: Data is erased one note or one percussion instrument (DRUMS part) sound at a time. • Hold and press this button, and press the keyboard key that corresponds to the note or percussion instrument (DRUMS part) sound you wish to erase. ALL ERAS: The performance recorded in the selected part is erased for as long as this button is pressed. (continued on the next page) 77 Composer Composer Part V Composer QUANTIZE: Smooth out any unevenness in the timing of your performance. • Before recording, select the note value for the desired quantize level. (The quantize level is shown on the display as QTZ-) SOLO: Mute all parts except the part which is currently being recorded. • A MUTE mark is shown for the other parts on the display. • To turn off the SOLO function, press this button again. KEY IN CHORD MODIFY (except for INTRO, ENDING, DRUMS): Use the GROUP and TYPE A and V buttons to select the type of pattern progression. • This setting is for the sound that is going to be recorded from this time. Chord Mollify Change For data that has already been recorded, you can select the type of pattern progression for the bass and accomp parts. • This function cannot be used for the INTRO and ENDING patterns. 3. Use the GROUP and MODIFY TYPE a and v buttons to select the corresponding progression type. • If a progression type for which the note name is displayed (in C key) was selected for the chord group, played notes which are not displayed are changed to notes which are displayed. 4. Use the FUNCTION a and v buttons to enable or disable the function. KEEP: No change. CHANGE: The change is enabled. 5. When you have finished making the settings for each part, press the OK button. 6. Press the EXIT button. Part Setting You can make detailed settings for each part. 1. On the REALTIME RECORDING display, press the PART SETTING button. • The settings comprise three pages of the display. Use the PAGE buttons to switch pages. 2. Use the PART A and ▼ buttons to select a part. 3. Use the a and v buttons to set the corresponding item. ¿¡¡PART SETTING E3BS ne.A-Uvil F-ATTTPN ? 7 PITCH POINT: The pitch at which the pattern progression sound is lowered by one octave. • When the root note of the specified chord is lower than the set pitch point, the pitch of that part is automatically raised by one octave, thus avoiding an unnaturally low accompaniment pitch. • This is effective only for the part for which the Melody group was selected in CHORD MODIFY CHANGE. SOUND: Use the panel buttons to select the sound. DIGI EFF: Set the DIGITAL EFFECT to on or off. • (SOUND) is the initialized setting of the sound. 1.0n the RECORDING display, press CHORD MODIFY CHANGE button. • The display looks similar to the following. 8*1 CHORD H0D1FY CHANGE HEHOftV: fl-Vari> PPITERH the 2. Use the PART A and ▼ buttons to select the part you wish to set. 5. Use the buttons below the display to switch to a different recording part, and proceed to record each part in turn. 6. When you have finished recording the rhythm, turn off the PROGRAM MENUS button. 78 Part V Composer 2D PRRT setting FHtT BKiWE wn nv «»I ORUnl 0 '“HIT 4(T 0 2 I DRUM2 0 ---- 40 0 2 BOSS Q CEHTER 0 0 2 ftCCOHPf Û LEFT 52 EH D ACC0ÜP2 0 RIGHT 52 40 O 2 1 ACC0MP3 0 CENTER 40 0 2 PCC0HP4 0 LEFT 26 40 0 2 : ACC0MP5 0 RIGHT 28 40 0 2 ' BALANCE: Adjust the volume balance. PAN: Adjust the stereo balance of each part (LEFT 64 - CENTER - RIGHT 63). • At “LEFT 64”, the sound is all the way to the left, at “RIGHT 63” all the way to the right. The center point is CENTER. REV: Depth of the REVERB (0 to 127). CHO: Depth of the CHORUS (0 to 127). BEND RANGE: Adjust the range of pitch change when PITCH BEND data is received (0 to 12). EQ-Hi: Sound correction in the high range. • Use the FC a and V buttons to adjust the standard frequency. Use the GAIN A and V buttons to set the ratio of change. EQ-Low: Sound correction in the low range. • Use the FC A and V buttons to adjust the standard frequency. Use the GAIN A and V buttons to set the ratio of change. Playback 1. In the RHYTHM GROUP section, press the MEMORY button. -RHYTHM GROUP K&U04 urni mee&j ballad uzzcoteo swc wotu ictaohoc o o o o o o □□□□□□ SOUL I fiOPEll COJCWfl VLlfCSMi HMCnl MCO BU'ES «STD* *C»Tlf mull O O 0 o o □□□CO The display looks similar to the following. g RHYTHM * Easy 16 Beat 1 C Easy Swing 2. Select the desired memory (A/B/C). 3. Use the VARIATION & MSA buttons to select a variation. 4. Press the START/STOP button. • The DRUMS part begins to play back. • The BASS and ACCOMP parts are played back when you use the AUTO PLAY CHORD. 79 Composer Composer Part V Composer Step Record Use STEP RECORD to store the notes one-b...

Herunterladen

Geben Sie zwei Ziffern: