Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Value Meaning L64 Hard Left C00 Center R63 Hard Right 2. If you are in Layer or Split mode, press SCROLL • again to go to select the L (Layer/Left) parameter (only available in Layer or Split mode): Pan 2 M:R07 • L:L07 3. While the Layer/Left (L) part is selected, use the +/YES and -/NO buttons to select a different value. 4. Press the EXIT button to return to the Main page and save the changes (see “Exit from the Sound edit mode” on page 38), or the SCROLL • button to go to the next edit page (see below). Editing sounds and performances > Adjusting the effects Adjusting the effects The C-720 is equipped with three types of effects: Effect Meaning IFX (Insert Effect) The sound pass entirely through this effect. This is used for effects being part of the sound itself, like the phaser of the rotary speaker. There is a separate IFX for each of the sounds. Rev (Reverb) This effect adds ambience to the sounds. In Layer or Split mode, there is a single reverb for all selected sounds. Ch (Chorus) This effect adds modulation to the sounds. In Layer or Split mode, there is a single chorus for all selected sounds. The following diagram shows the effect’s routing: Use the following parameters to select the reverb, chorus and insert effects, and adjust how much of the sound must be processed. Setting the reverb effect Reverb adds ambience to the sound. Either you are in Single, Layer or Split mode, a single reverb effect is available for both sounds (see diagram). A different amount of reverb can be applied to each sound, thanks to the Reverb Send parameter (see below). 1. After having pressed the EDIT button, use the SCROLL • button to go to the Reverb Type edit page, with the reverb type selected: Reverb Type 3 • Hall 1 On Use the +/YES and -/NO buttons to select a different reverb. See below the list of available reverb effects (a more detailed list is on page 71). Reverb Hall 1 Hall 2 Hall 3 Wet Plate Dry Plate Room 1 Room 2 Bright Room 2. Press SCROLL • again to select the Reverb On/Off parameter: Reverb Type 3 Hall 1 • On Use the +/YES and -/NO buttons to turn reverb on or off. This corresponds to the status of the REVERB indicator. 3. Press SCROLL • to go to the Reverb Send edit page, with the M (Main) parameter selected: Reverb Send 4 • M:127 L:100 Use the +/YES and -/NO buttons to set the amount of reverb applied to the Main sound (0 ~ 127). 4. If you are in Layer or Split mode, press SCROLL • again to select the L (Layer/Left) parameter: Reverb Send 4 M:127 • L:100 Use the +/YES and -/NO buttons to set the amount of reverb applied to the Layer/Left sound (0 ~ 127). 5. Press the EXIT button to return to the Main page and save the changes (see “Exit from the Sound edit mode” on page 38), or the SCROLL • button to go to the next edit page (see below). Editing sounds and performances > Setting the chorus or modulation effect Setting the chorus or modulation effect The chorus or modulation effect adds depth to the sound. Either you are in Single, Layer or Split mode, a single chorus effect is available for both sounds (see diagram above). A different amount of chorus can be applied to each sound, thanks to the Chorus Send parameter (see below). 1. After having pressed the EDIT button, use the SCROLL • button to go to the Chorus Type edit page, with the chorus type selected: Chorus Type 5 • Chorus Off Use the +/YES and -/NO buttons to select a different chorus effect. See below the list of available chorus-type effects (a more detailed list is on page 71). Chorus Chorus Harm. Chorus Chorus Delay Ensemble Flanger Tremolo 2. Press SCROLL • again to select the Chorus On/Off parameter: Chorus Type 5 Chorus • Off Use the +/YES and -/NO buttons to turn the chorus on or off. This corresponds to the status of the CHORUS indicator. 3. Press SCROLL • to go to the Chorus Send edit page, with the M (Main) parameter selected: Chorus Send 6 • M:127 L:Off Use the +/YES and -/NO buttons to set the amount of chorus applied to the Main sound (0 ~ 127). 4. If you are in Layer or Split mode, press SCROLL • again to select the L (Layer/Left) parameter: Chorus Send 6 M:127 • L:Off Use the +/YES and -/NO buttons to set the amount of chorus applied to the Layer/Left sound (0 ~ 127). 5. Press the EXIT button to return to the Main page and save the changes (see “Exit from the Sound edit mode” on page 38), or the SCROLL • button to go to the next edit page (see below). Setting the insert effects In addition to the reverb and chorus effects, common to both sounds in Layer and Split mode, an insert effect (IFX) is available for each sound (see diagram above). The insert effect strongly modifies the sound, and is to be considered as part of the sound itself. 1. After having pressed the EDIT button, use the SCROLL • button to go to the IFX Type edit page, with the IFX assigned to the Main sound selected: IFX M/L Type 7 • EQ1 Phaser Use the +/YES and -/NO buttons to select a different effect.“Off” means no effec...