Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Check the “STITCH SETTING CHART” at the end of this manual for patterns that can be used with the twin needle. CAUTION • Use only twin needles made for this machine (part code X59296-151). Other needles could break, resulting in damage. • Be sure to set the twin needle mode when using the twin needle. Using the twin needle while the machine is in single needle mode could cause the needle to break, resulting in damage. • Do not sew with bent needles. The needle could break and cause injury. • When using the twin needle, be sure to use presser foot “J”. In case bunched stitches may occur, use the presser foot “N”. a Press , and then install the twin needle (see “CHANGING THE NEEDLE” on page 33). b Thread the machine for the first needle according to the procedure for threading a single needle (see “Upper Threading” on page 27). c Pass the thread through the needle bar thread guide, and then manually thread the needle on the left side. * Do not use needle threader when threading a twin needle. a Needle bar thread guide a d Set the supplemental spool pin in the “up” position. a a Supplemental spool pin e Place the additional spool of thread on the supplemental spool pin so that the thread unwinds from the front. Then, slide the spool cap as far as possible onto the supplemental spool pin to secure the thread spool. a b c a Spool cap b Supplemental spool pin c Thread spool f While holding the thread from the spool in your right hand, hold the end of the thread with your left hand, and then pass the thread through the thread guide. * Do not pass the thread through the bobbin winding thread guide. a b a Bobbin winding thread guide b Thread guide LOWER/UPPER THREADING g While holding the thread from the spool with both hands, pull the thread through the lower notch in the thread guide plate, then through the upper notch. Hold the end of the thread with your left hand, and then guide the thread through the groove, following the arrows in the illustration. a a Shutter h Without passing the thread through the needle bar thread guide, manually thread the needle on the right side. a a Needle bar thread guide k Press to select the setting for twin needle sewing. * The stitch width becomes narrower than with single needle sewing. a a Single needle/twin needle setting > appears. CAUTION • Be sure to set the twin needle mode when using the twin needle. Using the twin needle while the machine is in single needle mode could cause the needle to break, resulting in damage. l Press the “Start/Stop” button after lowering the presser foot lever. Memo To change the sewing direction with the twin needle, raise the needle from the fabric, raise the presser foot lever, and then turn the fabric. 1 Getting Ready Note The needle threader cannot be used. Manually pass the thread through the eye of the needle from the front. If the needle threader is used, damage to the machine may result. i Press , or press in the screen. j Select a stitch. Note If appears as after a stitch is selected, the twin needle cannot be used with the selected stitch. 31 CHANGING THE PRESSER FOOT CHANGING THE PRESSER FOOT CAUTION • Always press in the operation panel before changing the presser foot. If is not pressed and the “Start/Stop” button or another button is pressed, the machine will start and may cause injury. • Always use the correct presser foot for the selected stitch. If the wrong presser foot is used, the needle may strike the presser foot and bend or break, and may cause injury. • Only use presser feet made for this machine. Using other presser feet may lead to accident or injury. Removing the Presser Foot a Press the “Needle Position” button to raise the needle. b Press . > The screen changes, and all keys and operation buttons are locked. Raise the presser foot lever. d Press the black button on the presser foot holder to remove the presser foot. a b a Black button b Presser foot holder Attaching the Presser Foot a Place the presser foot under the holder, aligning the pin on the foot with the notch in the holder, and then lower the presser foot lever so that the presser foot pin snaps into the notch in the holder. a b a Notch b Pin b Press , or press in the screen. > All keys and operation buttons are unlocked, and the previous screen is displayed. c Raise the presser foot lever. CHANGING THE NEEDLE 1 CHANGING THE NEEDLE CAUTION • Always press in the operation panel before changing the needle. If is not pressed and the “Start/ Stop” button or another operation button is pressed accidentally, the machine will start and injury may result. • Use only sewing machine needles made for home use. Other needles may bend or break and may cause injury. • Never sew with a bent needle. A bent needle will easily break and may cause injury. Getting Ready b Press . ¦ Checking the Needle Place the flat side of the needle on a flat surface (such as the needle plate or a piece of glass) and check that the gap between the needle and the flat surface is even. Note Nev...