Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Cleaning the machine surface If the surface of the machine is dirty, lightly soak a cloth in neutral detergent, squeeze it out firmly, and then wipe the surface of the machine. After cleaning it once with a damp cloth, wipe it again with a dry cloth. CAUTION . Unplug the power supply cord before cleaning the machine. Otherwise, injuries or an electric shock may occur. Cleaning the race Embroidery performance will suffer if dust collects in the bobbin case. Therefore, it should be cleaned periodically. Turn off the machine. a b Unplug the power supply cord from the power supply jack on the right side of the machine. CAUTION . Unplug the power supply cord before cleaning the machine. Otherwise, injuries or an electric shock may occur. Remove the embroidery unit. d Loosen the needle clamp screw and remove the needle (page 28). a b a Screwdriver b Needle clamp screw Grasp both sides of the needle plate cover, and e then slide it toward you. a a Needle plate cover • The needle plate cover is removed. f Remove the bobbin case. Grasp the bobbin case, and then pull it out. a a Bobbin case — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — iInsert the tabs on the needle plate cover into the needle plate, and then slide the cover back on. — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — iInsert the tabs on the needle plate cover into the needle plate, and then slide the cover back on. Use the cleaning brush or a vacuum cleaner to g remove any lint and dust from the race and bobbin thread sensor and their surrounding area. a b c a Cleaning brush b Race c Bobbin thread sensor Note • Do not apply oil to the bobbin case. • If lint or dust collects on the bobbin thread sensor, the sensor may not operate correctly. h Insert the bobbin case so that the .. mark on the bobbin case aligns with the .. mark on the race. a a b • Align the .. and .. marks. b c a .. mark b .. mark c Bobbin case • Make sure that the indicated points are aligned before installing the bobbin case. a a Needle plate cover CAUTION .Never use a bobbin case that is scratched. Otherwise, the upper thread may become tangled, the needle may break or embroidering performance may suffer. For a new bobbin case (part code: XD1855-351), contact your nearest authorized service center. .Be sure that the bobbin case is correctly installed, otherwise the needle may break. 3 Care and Maintenance 79 APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Attaching the Embroidery Foot APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Attaching the Embroidery Foot This section describes how to attach the embroidery foot "Q". Attaching the embroidery foot If you need to replace the embroidery foot, attach the embroidery foot "Q" as follows. b a a Embroidery foot bar b Caught by the presser foot holder screw CAUTION . Always use the embroidery foot "Q" when embroidering. If the wrong embroidery foot is used, the needle may hit the embroidery foot and bend or break. Press (Needle position button) once or a twice to raise the needle. a a Needle position button Note • The needle is correctly raised when the mark on the handwheel is at the top. Check the handwheel mark is at the top position. b Turn off the machine. CAUTION • Before attaching the embroidery foot, be sure to turn off the machine. Otherwise, injuries may occur if one of the operation buttons is accidentally pressed and the machine starts embroidering. Raise the presser foot lever. c a a Presser foot lever d Hold the embroidery foot "Q" with your right hand, as shown. Hold the embroidery foot with your index finger wrapped around the lever at the back of the foot. a a Lever — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — While pressing in the lever with your finger, fit e the embroidery foot bar over the needle clamp screw to attach the embroidery foot to the presser foot bar. c b a a Presser foot bar b Needle clamp screw c Embroidery foot bar f Secure the embroidery foot with the presser foot holder screw. Set the embroidery foot perpendicular. a a Presser foot holder screw Firmly tighten the presser foot holder screw. g Turn the screwdriver toward the front. CAUTION .Do not hit the needle with your finger or the embroidery foot when attaching it. The needle may break or cause injury. .Be sure to tighten the screw with the included screwdriver. If the screw is loose, the needle may hit the embroidery foot and break or bend. .Before embroidering, always turn the handwheel toward you (counterclockwise) slowly to make sure that the needle does not hit the embroidery foot. The needle may break or bend. 3 a a Screwdriver Attaching the Embroidery Foot 81 APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Troubleshooting APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Troubleshooting If the machine stops operating corre...