Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
. Do not turn on the machine while pressing down the foot controller. The machine may start unexpectedly and cause personal injury or damage to the machine. 1Turn on (toward the ‘I’ mark) 2Turn off (toward the ‘O’ mark) CAUTION ¦Checking the needle correctly Put the flat side of the needle on a flat surface. Check the needle from the top and the sides. Dispose of any bent needles safely. 21 Foot controller When you press the foot controller down lightly, the machine will run at a low speed. When you press harder, the machine’s speed will increase. When you take your foot off the foot controller, the machine will stop. 1 2 1 Slower 2 Faster You should make sure that nothing is placed on the foot controller when the machine is not in use. CAUTION . Do not allow pieces of cloth and dust to build up on the foot controller. Doing so could cause a fire or an electric shock. Note (For U.S.A. only) . Foot Controller: Model KD-1902 This foot controller can be used on the machine with product code 885-X06/X08/ X09/X26/X28. The product code is mentioned on the machine rating plate. The sewing needle must always be straight and sharp for smooth sewing. 1 2 1 Parallel space 2 Level surface (bobbin cover, glass, etc.) Replacing the needle CAUTION . Always turn off the machine before you change the needle. Otherwise, injuries may occur if the foot controller is accidentally pressed and the machine starts sewing. . Only use sewing machine needles for home use. Other needles may bend or break and cause injury. . Never sew with a bent needle. A bent needle will easily break and cause injury. 1 Turn off the machine. 2 Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. 3 Lower the presser foot lever. 1 1 Presser foot lever CAUTION CAUTION . Before replacing the needle, place fabric or paper under the presser foot to prevent the needle from falling into the hole in the needle plate. 4 Hold the needle with your left hand, and then use an oval screwdriver to turn the needle clamp screw counterclockwise to remove the needle. 21 1 Use an oval screwdriver 2 Needle clamp screw • Do not use excessive force when loosening or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged. 5 With the flat side of the needle toward the back of the machine, insert the needle until it touches the needle stopper. Next, tighten the needle clamp using an oval screwdriver. 2 3 1 1 Use an oval screwdriver 2 Needle stopper 3 Needle Install the twin needle in the same way. . Make sure you insert the needle until it touches the stopper, and securely tighten the needle clamp screw with an oval screwdriver, otherwise the needle may break or the machine may be damaged. Changing the presser foot CAUTION . Always turn off the machine before you change the presser foot. If you leave the power on and step on the controller, the machine will start and you may be injured. . Always use the correct presser foot for the stitch pattern you have chosen. If you use the wrong presser foot, the needle may strike the presser foot and bend or break, and may cause injury. . Only use presser feet that have been designed to be used with this machine. Using any other presser foot may cause accident or injury. You will have to change the presser foot depending on what you want to sew and how. 1 Turn off the machine. Raise the presser foot lever. 2 Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. 3 Press the black button at the back of the presser foot holder to release the presser foot. 1 2 3 1 Black button 2 Presser foot holder 3 Presser foot 4 Put a different presser foot on the needle plate so that the bar on the presser foot is in line with the slot on the shank. 8 KNOWING YOUR SEWING MACHINE KNOWING YOUR SEWING MACHINE 5 Lower the presser foot lever and fix the presser foot onto the shank. If the presser foot is in the correct place, the bar should snap in. 2 1 1 Shank 2 Bar ¦ Presser foot installation orientation CAUTION . If the presser foot is not installed with the correct orientation, the needle may strike the presser foot, which may bend or break the needle and cause injury. THE CONTROLS Pattern selection dial CAUTION . When you use the pattern selection dial to choose a pattern, raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. If the needle is in the down position when you turn the pattern selection dial, the needle, presser foot or fabric may be damaged. To choose a stitch, simply turn the pattern selection dial in either direction. The next section shows recommended stitch lengths and widths. 21 1 Pattern selection dial 2 Chosen pattern number Stretch stitching Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. ¦ 53 Stitches Setting the stitch length dial to “ 1 ” changes the se...