Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Euro-Pro Dateigröße: 4.45 mb Dateiname: Unterrichtssprache:

3. 4. Following the slotted threading path, pull the thread down to the thread check spring (inside) and lead it across from left to right. 5. Pull the thread upward and slip into the slotted hole of thread take-up level from left to fight© . 6. Draw the thread through guides (6) and © , and thread the needle from front to rear®, leave the thread about 15cm(6 inches) long underneath the presser foot. B 10 DRAWING UP THE BOBBIN THREAD 1.Hold the end of the needle thread with your left hand. 2.Turn the balance wheel slowly towards you with your right hand until the needle goes down and comes up. Then stop the balance wheel when the take-up lever is at its highest position. Lightly draw up the needle thread forming a loop with the bobbin thread. 3.Puil about 15cm (6 inches) of both threads away from you under the presser foot. STRAIGHT STITCH AND ZIGZAG STITCH Model 377 Model 374 Model 373/372/372H Presser foot zigzag foot zigzag foot Pattern selector M ( C+D ) or O ( ) (for straight gtitch) 1 - 5 (54321) (for zigzag stitch) A ( C+D ) or B ( Cp ) (for straight stitch) C ( CCjjCjC ) (for zigzag stitch) ( j ) (for straight stitch) ( jCCjCjC ) (for zigzag stitch) Stitch length dial 0.3-4 0.3-4 - Starting Sewing 1. Be sure both the threads are drawn back under the presser foot. 2. While holding the threads with your left hand, turn the balance wheel toward you to bring the needle into the fabric where you wish to start sewing. 3. Lower the presser foot, and press the speed controller gently, then start sewing slowly. *Sew a few reverse stitches by pushing reverse button for reinforcing the end of seams. *Raise the needle to its highest position before turning the pattern selector dial and stitch width dial. zigzag foot 11 English Changing Sewing Directions 1. Stop the machine, and turn the balance wheel toward you to bring the needle down into the fabric. Raise the presser foot. 2. Pivot the fabric around the needle to change direction as desired. 3. Lower the presser foot and continue sewing. Fastening Seams 1. For fastening the ends of seams, press in the reversing button and sew several reverse stitches. 2. To remove the fabric, raise the presser foot and draw the fabric away from you. 3. C ut threads on thread cutter at the rear of presser ba r or with a pair of scissors. Leave about 15 cm (6 inches) of hread hanging from the needle eye. TRIPLE STRETCH STITCH (Model 374/373/372/372H) If you wish to sew stretch fabrics, this is the right stitc h to avoid thread breaking. This is also very suitalbe for seams that need great strength,e.g.crutch seams or poc ket seams. TRIPLE STRAIGHT STRETCH STITCH TRIPLE ZIGZAG STRETCH STITCH ............................................. Model 377 Model 374 Model 373/372/372H Piessei foot zigzag foot — zigzag foot Pattern selector M( cjjp ) - 8( 111 ) Stitch length dial S.S. — — ........ ......................... Model 377 Model 374 Model 373/372/372H Presser foot zigzag foot — zigzag foot Pattern selector O( ) - 7( J ) Stitch length dial S.S. — — Note: * Use a STRETCH needle. The blue tipped shank needle effectively prevents skipped stitches. 12 TRICOT ZIGZAG STITCH This stitch is very suitable for darning tears. It can also be used for reinforcing stretch materials and sewing on fabric parts. ................................. Model 377 Model 374 Model 373/372/372H Piessei foot zigzag foot zigzag foot zigzag foot Pattern selector A ( ^ ) D (< > ) A A / V \ Stitch length dial 0.3 to 4 0.5 to 4 - SMOCKING STITCH With a na rrow strip of fabric directly under the line of gathering, stitch over the gathers. The design will be a series of small dia monds. When s moc king a ga rme nt, the stitching should be done before the piece is sewn into the ga rment. ^~ Model 377 Model 374 Model 373/372/372H Presser foot zigzag foot zigzag foot Pattern selector A ( %, ) 10( % ) Stitch length dial S.S. - Note: *Use a STRETCH needle. The stretch needle effectively prevents s kipped stitches. OVERLOCK STITCH With this seam it is possible to prevent raw edges, especially on easilyfraying fabrics,with a good-locking and lasting edge finish. ............——......................... Model 377 Model 374 Model 373/372/372H P resserfoot zigzag foot — zigzag foot Pattern selector D ( | ) — 9( i ) Stitch length dial S.S. — — P lace the fabric under the presser foot so that the stitches are made over the edge. Lower the presser foot and start sewing. G uide the material lightly as shown. Sew on a piece of waste fabric to check the machine setting. The overlock stitches are formed correctly when the needle sews to the right and just misses the fabric edge. Note: *Use a S TR ET C H needle. The stretch needle effectively prevents skipped stitches. 13 English DOUBLE ACTION STITCH This is a good stilch to use in attaching or binding elastic fabrics and stretch lace, lingerie stretch knit. The stitch is decorative as well as useful. ...

Herunterladen

Geben Sie zwei Ziffern: