Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: White Dateigröße: 1.44 mb Dateiname: 1117_white-1787,1899-x.pdf Unterrichtssprache:

3- 3. BEFORE SEWING in in Detachable Extension Table is a is lid it Changing Needle Set needle in the highestposition by turning handwheeltowards you. Loosen needle clamp screw andremove needle. With flat face away from you, insert a new needle into grooveof needle bar. Push needle until it reachesstopper a and tighten needle clamp screw firmly. Always use a straight needle with Proper needle a sharp point. straight shaft sharp point Using defective or worn needles not only causes stitch skipping, breakage of needles or snappingof thread; it also can damagehook and needle plate. -J 6— Changing Foot Raise presser foot lifter Set needle in the highest position by turning handwheel towards you 2 Snap-on Presser Foot: I, Push the lever a in the arrow direction so that the presser foot will come off Position a new foot with the pin a b right under the groove of the holder b Lower the presser foot lifter so that the foot will be automatically snapped on When you fail to catch the foot, push the lever in the arrow direction slightly Bobbin Winding Set needle in the highest positionby turning handwheel towardsyou. Open shuttle cover. Open latch of bobbin case andtake it out. —-- z I Close latch of bobbin case andbobbin comes out easily. —8— Push back to fold handle. 4 Pull out spool pin and put a felt on spool pin. 1 Put a spool on spool pin. 4 Draw thread from spool pin 2 through thread guide and pre tension device, following numb ers and 2 I Wind thread clockwise aroundbobbin several times. Push bobbin on to spindle. Holding handwheel with your lefthand disengage handwheel byunscrewing stop motion knob. L. —9— Push bobbin to right and press down foot controller. Machine stops automatically when bobbin is full. Push bobbin to left, to disengage>N from wheel. Take off bobbin from spindle and cut thread. Retighten stop motion knob. I If bobbin is wound unevenly as shown, open face cover and trouble loosen set-screw of the guide for bobbin winding: Use screw driver correction to adjust height. —10— inserting Bobbin I Place bobbin in its case with thread running in direction of arrow. ) Guide thread into slot a of / bobbin case. Pulling thread to left, bring it I under tension spring then todelivery eye .:. —11— loosen -J N 1 2 Adjusting Lower Tension To test bobbin tension, hang and shake bobbin case as shown. At proper tension bobbin case will gradually drop a small amount. To adjust tension, turn adjusting screw with small screwdriver. Raise needle in the highest position. Leave end of thread of about 1 0 cm (4”) from bobbin case. Take hold of latch and push bobbin case into shuttle Release latch when bobbin case is fully inserted. DROP FEED LEVER The leier is in the right side of shuttle cover. For normal sewing, move the lever to A4 position. To lower feed dog, move the lever to AEA position. This position is used for button sewing, darning and embroidery. Threading Upper Thread Raise lifter. Raise lever to by you. following - 7 guide I Lead side of disc 2 Hook it 3 from to 2 7 lever 4 to guide 5 from right to left, and guide 6 (left one) eye 7 Leave of of 15 cm (6”). 1 3— 7 1 Drawing Up Lower Thread . :‘ in a 15 (6) Foot Pressure re in If ibric, thread and needle table T eRFAD Nt DLE: T4 5 °l C E irop Mer e’zed CO ton Covered Fi rope in USSze Port REMARKS (‘elton C ottori Polyester Slk Nyon 705 iNst Style t’ SHEER ( ‘nO.s [on No 70 90 Silk N eki Do 3 9 Reguar Looser op 3cr 1cc DEER 13iojsn Crepe wJr J’qondv. T5feta 50 70 60 Silk Nylon eS 70 9 one n v to GOT i,...

Herunterladen

Geben Sie zwei Ziffern: