Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Lead thread either side of tensiondisc . Hook the thread under the guide ® as shown. - Thread take-up lever ®. Pass thread to guide from rightto left, and guide () (left one) then needle eye Y. Leave end of thread of about 1 5cm (6”). —14— - Drawing Up Lower Thread Hold of with left slowly Turn and you until up Pull slowly will up in a loop. threads Pull 15 (6”) together cm presser on left. Foot Pressure Push down the outer ring of the pressure regulator. This will release the pressure on the presser foot. To Increase the pressure. push down inner pin until suitable pressure is obtained. Insufficient pressure may cause poor feeding of the fabric, skipped stitches, or difficulty in guiding the fabric. If feed dogs or presser foot marks appear on the fabric. reduce the pressure. When sewing multiple thickness or heavy fabnc, reduce the pressure. Increase pressure when sewing lighter weight fabrics. —15— I I i I Pattern Selection Dial The desired stitch will be obtained by turning the stitch selector, it can be turned either to the right or to the left. Note: When operating selector, make sure needle is in the highest position. The Stitches Are Shown as Below. 4ODEL: 1510,2640,1919 Bartack stitch of buttonhole. Left side stitch of buttonhole. Right side stitch of buttonhole. Straight stitch (3 kinds of stitch 5 67length) 8,9, Zigzag stitch (4 kinds of zigzag10,1 lwidth) 12 Blind stitch. 13 Stretch blind stitch. 14 Mending stitch. 1 5 Straight stretch stitch16 Rickrack stitch. 1 7 Briar stretch stitch18 Feather stretch stitch19 Overcast stretch stitch(MODEL: 1505, 2440, 1805 Bartack stitch of buttonhole Left side stitch of buttonhole j Right side stitch of buttonhole Straight sde stitch (3 kinds of 5 67stitch length) 8,9,Zigzag stitch (3 kinds of10 zigzag width) 11 Blind stitch. 1 2 Straight stretch stitch 1 3 Overcast stretch stitch —18— 7. MAKING BUTTONHOLES Set machine as shown. I Determine Lengthmarking Measure diameter and thicknessof button and add 0.3cm (1 8”) 0.3cm(1/8”) for bar tacks. Mark buttonhole size on material. length of a diameter buttonhole I thickness Attach buttonhole foot. Completely push back sliding parta of buttonhole foot. Place material under foot so thatmarking of buttonhole passesthrough center of foot and arrow b of foot indicates beginning lineof marking. —22— Bar tacking: Set pattern selection dialto 1 ( ) andsew5-6 stitches. - Left side: Change pattern to 2 J ). Sew left side from front to back until it reaches end line, L Remember the point where arrow shows so that it is not necessary to mark end lines for alt buttonholes. Bar tacking: Change pattern to 3 and sew 5-6 stitches. ii Right side: Change pattern to 4 ) and sew right side until it catches first bar tack. .9 —23— Left and Right SideBalance of Buttonhole Stitch density on right and leftsides of buttonhole can be adjustby buttonhole balance controldial. This dial should usually be in a neutral position (between “±“ / and “—“) If the stitches on the right side ofthe buttonhole are too closetogether, turn the dial to the right(+).*Turning dial to right opens rightside and closes left side. + H H If the stitches on the right side ofthe buttonhole are too open, turn the dial to the left (—). * Turning dial to left closes right side and opens left side. Note: This dial can simultaneously adjust stretch stitch balance. Therefore please refer to page 31 when you move this dial. / —24 N) 0) (“U) o— -“ CDCD 00(0 - ‘S.’ 3CD CD 0 —.3 — cr- C) 0 on - 0C0D 3 0)_ — -I .73 CD (flCD 3 c3 0303 CD CD0) 0 -03 (00 :r —r4 0ci CD-. 03< ...L C) :7 00) (D -40 03 II cr CD 2. 0 0. Ow 0 (0 CD a)03 D 0 U) I Correct seam. right side wrong side Needle is catching edge of foldtoo much. . Needle is not catching edge offold at all. ) c) / Elastic Blind Hem Stitch (For model 1510, 1919 and 2640only.) For elastic materials, set machineas shown and sew in the sameway as for normal blind hemstitch. ,1 —28— F 10. SHELL STITCHJNG Silk, nylon organdy or similar sheer fabrics are suitable. Set machine as shown. Fold edge of material. With folded edge to left, place it under presser foot. Pull thread ends towards back when starting sewing. Make sure needle misses raw edge of fold when it moves side ways. 12. STRETCH STITCHING The stitches shown are all used with stretch and knit fabrics. These are special stitches built in the machine for your quick selection. Straight stretch Rickrack briar stretch Briar stretch Feather stretch Overcast stretch For model 1510, 1919 and 2640 only.) Adjusting Stretch Stitch Balance In stretch stitch sewing, the stretch stitch adjuster should usually be in a neutral position (between ‘+‘ and “—“). When sewing some fabrics, you may need to adjust this control to balance the stitches for appear ance sake. If design seems open like the illustriations to the left, adjust the control slightly toward until “— design looks like the center design. If the design appears to be closed as in the right hand illustrations, turn the control towa...
Dieses Handbuch ist für folgende Modelle:Nähmaschinen - 1919 (1.43 mb)