Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Operation buttons 1. Reverse button Hold down this button to sew either backwards or a reinforcement stitch at a low speed. 2. Auto-lock button Hold down this button to sew locking stitches immediately or at the end of the current pattern and automatically stop. 3. Needle up/down button Press this button to move the needle either up or down. 8 B. Function buttons 4. Stitch length Press this button to adjust the length of the stitch. 5. Stitch width Press this button to adjust the width of the stitch. 6. Pattern mirroring Press this button to sew a mirrored pattern. 7. Mode selection Press this button to select direct mode, utility and decorative pattern mode or block letter mode. C. Memory buttons 8. Clear button If an incorrect pattern is selected or programmed, pressing this button will clear it. 9. Arrow button Press the “ “ button or “ “ button until the desired stitch number in the programmed combination is displayed. 10. Memory button Press this button to enter or store the programmed pattern combination in the memory. D. Selection buttons 11. Direct pattern selection and number buttons Instant access to direct pattern or press the pattern number to select the desired pattern. LCD SCREEN - MODEL C10 LCD SCREEN - MODEL C10 Direct Pattern Auto-lock Reverse Needle up Mirror Buttonhole lever Bobbin winding Needle position Pattern number Stitch width Direct mode Suggested presser foot Stitch length Pattern Needle down Mirror Auto-stop Reverse Pattern number Normal mode Suggested presser foot Stitch width Memory Stitch length Current position in theprogrammed memory Total space in the memory 10 LCD SCREEN - MODEL C20 Direct Pattern Auto-lock Needle up Mirror Buttonhole lever Bobbin winding Reverse Needle position Pattern number Stitch width Direct mode Suggested presser foot Stitch length Pattern Needle down Mirror Auto-stop Reverse Pattern number Stitch width Current position in theprogrammed memory Normal mode Memory Total space in the memory Suggested presser foot Stitch length Alphabet Needle up Auto-stop Pattern number Stitch width Current position in theprogrammed memory Total space in the memory Memory Suggested presser foot Stitch length Alphabet mode PATTERN CHART - MODEL C10 The portion marked in color on the chart below shows the one unit of each pattern. PATTERN CHART - MODEL C10 The portion marked in color on the chart below shows the one unit of each pattern. A. Direct selection patterns B. Pattern selection by number 12 B. Pattern selection by number C. Alphabets B. Pattern selection by number C. Alphabets PATTERN CHART - MODEL C20 The portion marked in color on the chart below shows the one unit of each pattern. A. Direct selection patterns ACCESSORIES ACCESSORIES 1. Standard foot (T) 2. Zipper foot (I) 3. Buttonhole foot (D) 4. Overcasting foot (E) 5. Blindhem foot (F) 6. Satin stitch foot (A) 7. Button sewing foot (only for C20). 8. 1/4. Quilting foot (P) 9. Free-motion/darning foot 10. Pack of needles 11. Spool pin felt 12. Second spool pin 13. Brush/ Seam ripper 14. Spool cap (Large) 15. Spool cap (Small) 16. Seam guide 17 Bobbins 18. Screwdriver (L & S) 19. Hard cover 123 4 5678 9 10 1112 13 14 15 1617 18 19 14 CONNECTING THE MACHINE TO THE POWER SOURCE Caution: Always make sure that the machine is unplugged from power source and the main switch is on “O” when the machine is not in use and before inserting or removing parts. ONOFF Before connecting the power supply, make sure that the voltage and frequency shown on the machine is conforming with your electrical power. Place the machine on a stable table. 1. Connect the power line cord to the machine by inserting the 2-hole plug into the terminal box. 2. Connect the power line plug to the electric outlet. 3. Turn on the power switch. 4. The light bulb will light up when the switch is turned on. To disconnect, turn the power switch to the off position, then remove plug from outlet. For USA and Canada This appliance has a polarized plug (one blade wider than the other), to reduce the risk of electrical shock; this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way. STARTING SEWING STARTING SEWING Foot control Speed adjustment lever The speed adjustment lever can control the sewing speed. To increase the speed, slide the lever to right. To decrease the sewing speed, slide the lever to the left. With the sewing machine turned off, insert the foot control plug into its connector on the sewing machine. Turn on the sewing machine, and then slowly depress the foot control to start sewing. Release the foot control to stop the sewing machine. Attention: Consult a qualified electrician if in doubt as how to connect the machine to the power source. Unplug the power cord when the machine is not in use. The appliance must be used with the foot controller C-9000. 16 instructions. A. back. B. can occ...
Dieses Handbuch ist für folgende Modelle:Nähmaschinen - HUSKYSTAN C20 (3.85 mb)