12 Box Contents.............................................................................................. 12 Machine Placement ...................................................................................... 13 Cleaning Machine......................................................................................... 13 Air Hose Installation ..................................................................................... 14 Sanding Belt Installation .................................

Note: When using an adapter, the adapter must be grounded. This equipment must be grounded. Verify that any existing electrical out- let and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a separate 12 AWG copper grounding wire from the outlet to a known ground. Under no circumstances should the grounding pin from any three-pronged plug be removed or serious injury may occur. Figure 2. Never remove the grounding pin! -6 M1104, M1105, M1106 Heavy-D

Omitting the discs can put uneven stress on the wheel causing it to crack and possibly fly apart. ALWAYS “ring test” a wheel before assembly to make certain it has no cracks or flaws. OPERATIONS -13 M1104, M1105, M1106 Heavy-Duty Bench Grinder MAINTENANCE General MAINTENANCE Check for the following conditions and repair or replace when necessary: • Cracked or loose grinding wheel. • Loose mounting bolts. • Worn switch. • Worn or damaged cords and plugs. • Any other condition that could hamper th

Figure 6. Tool rest and eye shield assembly. NEVER assemble a grinding wheel on the arbor without paper or fiber discs between the wheel and the mount- ing flange. Omitting the discs can put undue stress on the wheel, causing it to crack and possibly fly apart. Figure 7. Grinding wheel installation order. SET UP -9 M1104, M1105, M1106 Heavy-Duty Bench Grinder Test Run SET UP Once your machine is mounted and assembled, you should perform a test run to make sure it works properly. To perform a tes

1. Open circuit in motor or loose connections. 2. Start capacitor is at fault. 3. Short circuit in motor or loose connections. 4. Incorrect fuses or circuit breakers in power supply. 1. Inspect/repair all lead connections on motor for loose or open connections. 2. Replace start capacitor. 3. Inspect all connections on motor for loose or shorted terminals or worn insulation. 4. Install correct fuses or circuit breakers. Motor overheats, stalls (resulting in blown fuses or tripped circuit). 1. Mot

Immediately replace a damaged extension cord. Amp Rating Length and Gauge 25ft 50ft 100ft 0-6 #18 #16 #16 7-10 #18 #16 #14 11-12 #16 #16 #14 13-16 #14 #12 #12 17-20 #12 #12 #10 21-30 #10 #10 No 17. Keep proper footing and balance at all times. 18. Do not leave machine unattended. Wait until it comes to a complete stop before leaving the area. 19. Perform machine maintenance and care. Follow lubrication and accessory attachment instructions in the manual. 20. Keep machine away from open flame. Op

Always use an extension cord that uses a ground pin and connected ground wire. Use an extension cord that meets the amp rating on the motor nameplate. If the motor is dual voltage, be sure to use the amp rating for the voltage you will be using. If you use an extension cord with an undersized gauge or one that is too long, excessive heat will be generated within the circuit, increasing the chance of a fire or damage to the circuit. 17. KEEP PROPER FOOTING AND BALANCE at all times. 18. DO NOT LEA

SETUP Buffer Assembly Motor 1/2" Plywood Piano Hinge Rotation Working Side Figure 6. Side view of motor mounting behind. -9 W1681 Buffing Assembly OPERATIONS OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine. If

Hold the sander upside down with its top against a flat, stable surface. 3. Place the sandpaper over the base and align the holes in the paper with holes in the base (Figure 1). Figure 1. Sandpaper and base holes aligned. Model D3736 Palm Finishing Sander Tip: Try using the sandpaper that came with your sander as a template for cutting holes in new 1.4 sheets to match those on the bottom of the sander—so the dust bag can collect dust particles. Use a paper punch to cut the holes; or mark the hol

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. #7818JK Printed in China WARNINGSome dust created by power sanding, sawing, grind- ing, drilling, and other construction activities con- tains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and othe