Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Keep the open side of the guard away from the operator at all times. Edge grinding should only be done with wheels specifically designed for this purpose. REMOVING GUARD FOR SANDING OR USING FLAT WIRE BRUSHES • Set the Angle Grinder on a flat surface with the spindle facing up. • Remove the inner and outer flanges, unscrew spring washer and remove the guard. • Store these parts carefully. • Replace the guard after the job is finished. ATTACHING SANDING DISC • To remove the guard, see instructions given in the “Removing Guard for Sanding or Using Flat Wire Brushes” Section above. • Set the inner flange and outer flange on the spindle. • Push in the spindle lock button. Turn the spindle until it locks into place. • Once the spindle is locked, tighten the sanding disc by hand. OPERATING THE ANGLE GRINDER Always unplug the tool before attempting to change the guard or accessories. OPERATING THE ON/OFF SWITCH Never switch the Angle Grinder “ON” or “OFF” while under load conditions. WARNING 12 ATTACHING WHEELS WITH DEPRESSED CENTERS Always check the tool warning label for the recommended speed rating on accessories. Never run a wheel or brush over the rated speed. Accessories exceeding the recommended speed may fly apart and cause serious personal injury. Hubbed wheels do not require mounting flanges. • Press the spindle lock firm and insure there is no movement in the spindle. Then while the spindle lock is depressed tighten the locking nut in a clockwise direction using the pin spanner. • Allow the Angle Grinder to run in idle for at least a minute with the grinding or cutting disc correctly assembled. ATTACHING WIRE BRUSHES Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are necessary. WARNING 11 • Place the backing washer over the spindle making sure the fit is tight. • Place the grinding or cutting disc on the top of the backing washer ensuring the bore fits into the step of the flange. • Mount the concave recess side of the locking nut over the spindle. SPINDLE LOCK BUTTON • Guide back and forth over the work piece in a steady motion. • When cutting avoid tilting the Angle Grinder in the cutting plane. Ensure the cutting wheel has a clean cutting edge. • To cut hard stone a diamond cutting wheel is recommended. • Do nut use cutting wheel for rough grinding. MAINTENANCE AND CLEANING Always UNPLUG the tool from the power source before cleaning or maintenance. • The armature and motor are the heart of the power tool. Exercise care to ensure they do not become damaged or effected by oil or water. • Inspect the carbon brushes regularly and replace them when they are worn. (about 1/3 of the way up) • Regularly inspect all mountings and screws and ensure they are properly tightened. Failure to do so may result in serious damage. • Consult an authorized maintenance service agent in event of damage. • Clean and dust the Angle Grinder after each use. • Use compressed air to blow out any accumulated dust or grit. Tiny particles from metal grinding often accumulate inside your tool and could create an electrical shock hazard. • Never use solvents or harsh chemicals. Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the casing. Never immerse any part of the tool in a liquid. Always keep the ventilation openings clear. • Regularly clean the ventilation slots in your tool using a soft brush or dry cloth. ACCESSORIES Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessary for your power tool. If not, your tool may experience a loss of power, excessive voltage drop or overheating. The smaller the gauge number, the heavier the cord (see table on next page). 14 Always allow the Angle Grinder to come up to full speed before touching any surface. Always take the tool away from the workpiece before turning the tool “OFF”. Let the tool come to a complete stop before setting it down. This tool operates best under light pressure. Exerting heavy pressure will not speed up the work and may cause damage to the motor. • When starting hold the Angle Grinder firmly with both hands. One hand on the rear handle or the motor housing and the other hand on the side handle. • The switch can be locked in the “ON” position, a convenience for long grinding operations. • To turn the Angle Grinder “ON” without locking it, apply pressure to the switch button. When pressure is released, the switch button snaps to the “OFF” position. • To lock th switch “ON”, press the switch button forward and press the lock button. • To unlock the switch, simply press and release the lock button. Switch is spring loaded and will snap back automatically. USING THE ANGLE GRINDER: For best tool...