Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
For example – SJTW-A to indicate it is acceptable for outdoor use. RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. Nameplate Ampere Rating 0-2 18 18 18 16 16 14 14 12 12 2-3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 14 12 12 10 10 8 8 5-6 18 16 14 12 10 10 8 8 6 6-8 18 16 12 10 10 8 6 6 6 8-10 18 14 12 10 8 8 6 6 4 10-12 16 14 10 8 8 6 6 4 4 12-14 16 12 10 8 6 6 6 4 2 14-16 16 12 10 8 6 6 4 4 2 16-18 14 12 8 8 6 4 4 2 2 18-20 14 12 8 6 6 4 4 2 2 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable angle grinders are designed for numerous grinding operations. Typical applications are auto body grinding, smoothing welding beads, removing gates and flash from castings, removing rust and the like. TO START AND STOP THE TOOL Make sure that the switch is “OFF” and power circuit voltage is the same as that shown on the specification plate. 1. Connect the tool to the power circuit. 2. Grip the tool firmly to resist starting torque. 7 3. Push forward on the switch release lever (A) Fig. 1 as you squeeze the switch paddle (B) to turn the tool “ON”. 4. Release, the switch paddle to return to the "OFF" position. Allow the tool spindle to stop rotating before putting the tool down. A B . . Fig. 1 ASSEMBLY TO INSTALL AUXILIARY HANDLE An auxiliary handle (H) Fig. 2 is furnished with this tool and can be installed on either side or on top of the front housing. THIS HANDLE SHOULD BE USED AT ALL TIMES TO MAINTAIN COMPLETE CONTROL OF THE MACHINE. TO INSTALL WHEEL GUARD A TYPE 27 wheel guard is furnished with the machine. A TYPE 1 wheel guard is available as an accessory. Both guards are installed and adjusted in the same manner. H Fig. 2 A B Fig. 3 Always use an approved and properly adjusted wheel guard. DISCONNECT TOOL FROM POWER SOURCE. 1. Rest the tool on its back with spindle facing up. 2. Align the protrusion (A) Fig. 3 on the guard flange with the slot (B) Fig. 3 on the mounting flange of the gear housing cover. 3. Seat the guard on the mounting flange. Rotate the guard to a position that will place the guard between the operator and the grinding wheel (or any other accessory requiring a guard). Tighten the clamp screw (A) Fig. 3A to secure the guard in proper position (see Fig. 4). 8 A A Fig. 3A Fig. 4 Always make sure that the wheel guard is positioned between the operator and the wheel, so that flying chips or pieces of a wheel that might break will be deflected away from the operator (see Fig. 4). TO INSTALL GRINDING WHEEL DISCONNECT TOOL FROM POWER SOURCE. 1. Rest the tool on its back with the spindle facing up. 2. Install and adjust the appropriate wheel guard following instructions in “TO INSTALL WHEEL GUARD” section of this manual. 3. Position the inner flange (A) Fig. 5 on the spindle (C) with the round hub facing outward, away from machine. Rotate the flange until it drops into place on the spindle. Use Type 1 Wheel Guard when using Type 1 Wheels. 4. Place the grinding wheel on the spindle. 5. Place the outer flange (B) Fig. 6 on the spindle with the flat side against the wheel and thread into place hand- tight. 6. Depress the spindle lock pin (E) Fig. 7, and hold while rotating the grinding wheel clockwise by hand until the spindle lock engages. 7. Continue holding the spindle lock pin while placing the lugs of the handle wrench (F) Fig. 7 into the holes of the outer flange. Tighten securely by turning clockwise. AC Fig. 5 E F B Fig. 6 Fig. 7 9 OPERATION USING A DISC GRINDER Be certain that the wheel guard and auxiliary handle are installed. Firmly grip the auxiliary handle and motor housing (Fig. 8). Lift up the rear of the motor housing so that only the front section of the grinding wheel contacts the work. Use light pressure. Always lift the grinder off the work before starting or stopping the motor. The arrow on the front gear housing indicates the direction in which the grinding wheel rotates. Fig. 8 MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear safety glasses while using compressed air. FAILURE TO START Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line. LUBRICATION This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. No further lubrication is necessary. BRUSH INSPECTION AND LUBRICATION For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-...