Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Mount wheel on a rod or pencil through arbor hole and tap the side of the grinding wheel (in the positions shown in Figure 4) with a light, non-metallic implement such as the handle of a screwdriver. A sound and undamaged wheel will give a clear tone. If cracked, there will be a dead or dull sound and not a clear ring. If damaged, the wheel should not be used. 7. As the grinding wheel diameter decreases with use, the position of the work rest should be adjusted. Optimally, the distance between the outer diameter of the grinding wheel and the inner edge of the work rest should be less than the thickness of the material being ground but not more than 1/8" (3 mm). If not, loosen the two retaining bolts with each work rest, set the correct gap, and fully tighten. 8. For safe use, keep the standardequipped eye shields in position at all times. 9. Before switching on the grinder, turn the grinding wheel by hand to make sure it is not striking the work or tool rest. 10. Always use guards and eye shields. 11. Do not over tighten wheel nut. 12. Use only flanges furnished with the grinder. Assembly Before assembling the packaged parts, carefully check the parts for damage. If the parts (e.g. guards) are damaged to the point where they no longer perform their intended function, they should be properly repaired or replaced. With the grinder disconnected from the power supply and when working with the right side of the grinder first, position the spark arrester shown in Figure 5 onto the inner metal grinding wheel guard and attach it via the smaller supplied hex bolt, lockwasher, and flat washer. The mounting hole for this bolt is the smaller diameter one on the top of the inner guard, nearest the user. Tighten the securing bolt so that the spark arrester is close to, but not touching the grinding wheel. A gap between the two parts should be maintained at approximately 1/16 inch [1.5mm]. Using the remaining bolt hole on the top of the inner wheel guard, then attach the eye shield via the bolt with the black knob and the metal adapter which fits over the U-shaped support. Secure the eye shield by hand tightening the black knob. Note: The eye shield should be centered over the grinding wheel in this position. If not, use the other supplied eye shield assembly. If there is any protective material over the clear eye shield, remove it at this time. The work rests are now to be installed via the two remaining bolt holes in the bottom of the inner guard and the larger supplied hex bolts, lockwashers, and flat washers. Two of each should be used to secure each work rest. Note: The work rest which has the drill bit groove stamped at an angle in it should be used for the right hand assembly. The inner edge of the work rest should be positioned so that its distance from the outer diameter of the grinding wheel is less than the thickness of the material to be ground, but not more than 1/8 inch [3mm]. Once this distance is set, securely tighten both retaining bolts. When complete, spin the grinding wheel by hand to insure that none of these assembled parts contact the wheel. The finished assembly should look like that shown in Figure 6. Repeat the process for assembling the remaining supplied parts to the left side of the grinder. Mounting If the bench grinder has a tendency to tip over, slide, or walk on the supporting surface, then it should be securely mounted. To do so, first make sure that the grinder is disconnected from the power supply. Then secure the bench grinder using the mounting holes provided in the base of the grinder and screws (not provided). 4 Figure 5 Operating Instructions Figure 6 Figure 4 45° 45° 45° 45° Heavy wheels - support on clean hard floor Light wheels - support from hole by small pin or finger “TAP” HERE “TAP” HERE Safety g l asses must be worn during operation. Manual de Instrucciones DG490500CK, DG490700CK 4. Deje que la rueda alcance la 9. Antes de encender la rectificadora, KNIVES Informaciones Assembly (Cont’d.) Operation velocidad maxima despues de gire la rueda abrasiva manualmente Remove material from BOTH faces or Generales de encenderla y ANTES de comenzar a para asegurarse de que no golpee el sides of most knives. Work from the Changing Grinding Wheels usar la rectificadora. trabajo ni el apoyo de la herramienta. heavy (thicker) end of the knife to the tip. Seguridad (Continuacion) To change a grinding wheel, first 5. Reemplace las ruedas rotas, 10. Siempre use los protectores SCREWDRIVERS (FLAT HEAD) unplug the grinder from the power source. Remove the three screws and astilladas o danadas de inmediato. y la proteccion para los ojos. The end of a properly sharpened the outer grinding wheel guard which Make sure the bench grinder is OFF screwdriver will form a perfect, even edge 6. Asegurese de que la rueda que tiene 11. No ajuste de mas la tuerca de la La herramienta correcta hara el trabajo they secure. before you plug it in. Turn the bench -- flat and perpendicular to the ...
Dieses Handbuch ist für folgende Modelle:Schleifmaschinen - DG490700CK (2.05 mb)