Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Please refer to Dynabrade’s Warning/Safety Operating Instructions for more complete safety information. Index Key No. Part Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 50187 3" Dynapad Exhaust Cover 01734 15,000 RPM 01738 18,000 RPM 01748 20,000 RPM 01744 Silencer 01708 Rotor Nut 01007 Bearing 01121 Shim (3/pkg.) 01008 Plate 50767 Guide Pin (2) 01010 Spacer 01028 Cylinder 55025 Rotor 01185 Blade (4/pkg.) 01743 Bearing Plate 02649 Bearing 53163 Handle Assembly 01739 Motor Assembly 01437 Plug 01548 Gasket 01461 Lock Nut 01558 Collar Housing 01895 Model -52410 01896 Model -52411 01897 Model -52412 95558 Retaining Ring 01448 Throttle lever 01462 Safety Lock Lever 12132 Pin 01449 Valve Stem 95730 O-Ring 01024 O-Ring 01469 Speed Regulator Assy. 01464 Seal 01472 Tip Valve 01468 Spring 01494 Inlet Bushing 1 2 3 4 5 6 7 8 15 16 10 11 8 139 14 18 20 22 23 24 25 26 27 28 29 30 31 17 Oil: O1 = Air Lube O KEY 17 N•mT 45 N•mT 34 N•mT 23 N•mT O1 A8 A8 O1 A8 19 21 32 Right Hand Threads Left Hand Threads12 A T Adhesive: A8 = Loctite #567 Torque: N•m x 8.85 = In. - lbs. See reverse side for Accessories and Important Operating, Maintenance and Safety Instructions. Important Operating, Maintenance and Safety Instructions Carefully read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool. Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration. Operating Instructions: Warning: Eye, face, sound, respiratory and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety procedures posted in workplace. 1. With power source disconnected from tool, securely fasten abrasive/accessory on tool. 2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging valve body housing. 3. Connect power source to tool. Be careful not to depress throttle lever in the process. 4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be serviced to correct the cause before use. 5. Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electrical power sources. Sanding/Grinding certain materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Sanding/Grinding can cause sparks which can cause fires or explosions. It is the users responsibility to make sure the work area is free of flammable materials. Maintenance Instructions: 1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct the cause before use. 2. Some silencers on air tools may clog with use. Clean and replace as required. 3. All Dynabrade Rotary Vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specifications state 40 SCFM, set drip rate of your filter-lubricator at 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt. 473 ml.) is recommended. 4. An Air Line-Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11405 Air Line Filter-Regulator-Lubricator – Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports. 5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine. 6. A Motor Tune-Up Kit (P/N 96044) is available which includes assorted parts to help maintain motor in peek operating condition. 7. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones, chlorinated hydrocarbons or nitro carbons. 8. DO NOT clean or maintain air tools with chemicals that have a low flash point (example: WD-40®). Safety Instructions: Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent from Dynabrade, Inc. • Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI). • Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins. • Always disconnect power supply before changing abrasive/accessory or making machine adjustments. • Inspect abrasives/accessories for damage or defects prior to installation on tools. • Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complet...