Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
6. REMOVE adjusting keys or blade wrenches before turning a tool "ON". A wrench that is left attached to a rotating part of a tool may result in personal injury. 7. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 8. ALWAYS SECURE YOUR WORK. Use clamps or a vise to hold work when practical. It issafer than usingyour hand and frees both hands to operate tool. 9. USE SAFETY EQUIPMENT. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. 4 TOOL USE AND CARE SAFETY /_ WARNING: BE SURE to read and understand all instructions before operating this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. 1. ALWAYS use clamps or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. DO NOT force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 3. DO NOT use the tool if switch does not turn it "On" or "Off". Any tool that cannot be controlled with the switch is dangerous and must be repaired. 4. DISCONNECT the plug from the power source before making any adjustments, changing accessories or storing the tool. Such preventive safety measures reduce the risk of starting the tool ac('identally. 5. STORE idle tools out of the reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 6. MAINTAIN tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. 7. Keep sandpaper clean, remove excess build-up of dust and debris. Replace sandpaper when worn, this will provide better sanding results. 8. CHECK for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 9. USE ONLY accessories that are recommended for this tool. Accessories that may be suitable for one tool may become hazardous when used on another tool. hazard, especially oil finishes I /_ WARNING: Empty dust bag before storage when resin coating or linseed to help prevent have been sanded. possible fire ELECTRICAL SAFETY the terminals of plug when installing or removing I_ WARNING: Do not permit fingers to touch the plug from the outlet. @ Cover of Grounded ® Outlet Box ------ 1. Double insulated tools are equipped with a polarized @ plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. 5 ELECTRICAL SAFETY I /_ WARNING: Do not permit fingers to touch tire terminals of plug when J installing or removing the plug from the outlet. I 2. Double insulation [] eliminates the need for the three-wire grounded power cord and grounded power supply system. Applicable only to Class II (double-insulated) tools. This tool is a double insulated tool. Double insulation J J /_precautionsWARNING:when operating this tool. DOES NOT take the place of normal safety I 3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within the voltage marked on the tool's data plate. DO NOT use "AC only" rated tools with a DC power supply. 4. AVOID body contact with grounded surfaces, such as pipes, radiators, ranges and refrigerators.There isanincreasedriskofelectricshockifyourbodyisgrounded. 5. DO NOT expose power tools to rain or wet conditions or use power tools in wet or damp locations. Water entering a power tool will increase the risk of electric shock. 6. INSPECT tool cords for damage. Have damaged tool c,ords repaired at a Sears Service Center. BE SURE to stay constantly aware of the cord location and keep it well away from moving parts. 7. DO NOT abuse the cord. NEVER use the cord to carry the tool by or to pull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cordsincreasethe riskofelectricshock. EXTENSION CORDS Use a proper extension cord. ONLY use cords listed by Underwriters Laboratories (UL). Other extension cords can cause a drop in line voltage, resulting in a loss of power and overheating of tool. For thistool an AWG (American Wire Gauge) size of a least 14-gauge is recommended for an extension cord of 25-ft. or less in length. Use 12-gauge for an extension cord of 50-ft. Extension cords 100-ft. or longer are not recommended. Remember, a smaller wire gauge size has greater capacity than a larger numbe...