Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Bosch Dateigröße: 2.37 mb Dateiname: Unterrichtssprache:

4" Dia. 4" Dia. Max. wire cup brush 3" Dia. 3" Dia. 3" Dia. Max. sanding disc 4 1/2" Dia. 5" Dia. 6" Dia. "LOCK-OFF" SWITCH RELEASE LEVER PADDLE SWITCH GUARD RELEASE / ADJUSTMENT BUTTON VENTILATION OPENINGS GRINDING WHEEL WHEEL GUARD SIDE VIBRATION HANDLE CONTROL SIDE HANDLE SPINDLE LOCK FIG. 1 BM 1609929J65 02-08 2/20/08 11:30 AM Page 6 BM 1609929J65 02-08 2/20/08 11:30 AM Page 7 BM 1609929J65 02-08 2/20/08 11:30 AM Page 7 Assembly WHEEL GUARD INSTALLATION !WARNING Wheel guard must be attached when using disc grinding wheels. Always keep wheel guard between you and your work while grinding. The position of the guard can be adjusted to accommodate the operation being performed. To attach wheel guard DISCONNECT tool from power source. Position wheel guard on spindle neck so that the arrow on guard lines up with the arrow on the spindle neck. Rotate wheel guard clockwise 90. until it clicks in place (Fig. 2). TO ADJUST GUARD: depress guard release button (Fig. 1), rotate guard to desired position, release button and let it click in place. LOCK NUT AND BACKING FLANGE Your tool is equipped with a threaded spindle for mounting accessories. Always use the supplied lock nut (and backing flange) that has same thread size as spindle. TO REMOVE GUARD: Depress release button, rotate guard until arrow on guard lines up with arrow on spindle neck, and remove guard from spindle neck. FIG. 2 WHEEL SPINDLE GUARD NECK SIDE HANDLE The side handle used to guide and balance the tool can be threaded into the front housing on either side of the tool, depending on personal preference and comfort. Use the side handle for safe control and ease of operation. Disc Grinding Wheel Assembly (Models 1810PD, 1810PSD, 1811PS & 1811PSD only) Disconnect tool from power source. Be sure that wheel guard is in place for grinding. Place BACKING FLANGE and GRINDING WHEEL on the spindle. Thread on the lock nut and tighten nut using the supplied lock nut wrench, while holding the spindle lock in (Fig. 3). TO REMOVE: Reverse procedure. SPINDLE TYPE 27 GRINDING WHEEL BACKING FLANGE LOCK NUT FIG. 3 SPINDLE WHEEL GUARD BACKING FLANGE GRINDING WHEEL LOCK NUT -7 Disc Grinding Wheel Assembly (Model 1812PSD only) Disconnect tool from power source. Be sure that wheel guard is in place for grinding. When using spin-on grinding wheels, thread directly onto the spindle. When using mounting wheels, thread BACKING FLANGE onto spindle, then place GRINDING WHEEL on the spindle. Thread on the lock nut and tighten nut using a lock nut wrench provided with adapter kit, while holding the spindle lock in (Fig. 4). TO REMOVE: Reverse procedure. -8- Sanding Accessories Assembly BACKING PAD Before attaching a backing pad be sure its maximum safe operating speed is not exceeded by the nameplate speed of the tool. Wheel guard may not be used for most sanding operations. Always reinstall wheel guard when converting back to grinding operations. TO INSTALL BACKING PAD AND SANDING DISC Disconnect tool from power source. Set the tool on its top side (spindle up). Place the rubber backing pad onto the spindle shaft. Center the sanding disc on top of the backing pad. Insert the lock nut through the disc and thread onto the spindle as far as you can with your fingers. Press in the spindle lock, then tighten the backing pad securely with lock nut wrench (Fig. 5). TO REMOVE BACKING PAD AND SANDING DISC Disconnect tool from power source. Using the lock nut wrench unscrew the nut from the spindle, while holding spindle lock in. WIRE BRUSH ASSEMBLY Before assembling wire brush to this tool, disconnect from the power source. Wire brushes are equipped with their own threaded hub, simply thread on to spindle. Be sure to seat against shoulder before turning ! WARNING tool “ON”. SANDING DISC BACKING PAD LOCK NUT WIRE BRUSH SPINDLE FIG. 5 GRINDING WHEEL LOCK NUT SPINDLE TYPE 27 WHEEL GUARD BACKING FLANGE FIG. 4 TYPE 1 WHEEL GUARD (Included with model 1812PSD only) ! WARNING BM 1609929J65 02-08 2/20/08 11:30 AM Page 8 BM 1609929J65 02-08 2/20/08 11:30 AM Page 9 BM 1609929J65 02-08 2/20/08 11:30 AM Page 9 Operating Instructions !WARNING Hold the tool with both hands while starting the tool, since torque from the motor can cause the tool to twist. Start the tool before applying to work and let the tool come to full speed before contacting the workpiece. Lift the tool from the work before releasing the switch. DO NOT turn the switch “ON” and “OFF” while the tool is under load; this will greatly decrease the switch life. PADDLE SWITCH WITH "LOCK-OFF"FEATURE (Models 1810PSD, 1811PSD & 1812PSD only) The Paddle switch enables the operator to control the switch functions of "Lock-OFF", and "ON/OFF". TO UNLOCK SWITCH AND TURN TOOL "ON": Push "Lock-OFF" switch release lever backward to unlock paddle switch, then squeeze paddle switch (Fig. 6). TO SWITCH TOOL "OFF": Release pressure on paddle lever. The switch is spring loaded and will return to "OFF" position automatically. PADDLE SWITCH WITH "LOCK-OFF"...

Herunterladen

Geben Sie zwei Ziffern: