Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Wrap your cord loosely around the two hooks on the handle. Remove brushes after use. The bristles may be damaged due to the weight of the machine. Store your machine in the upright position. After each use, remove wax or cleaning solutions. After sanding, blow sawdust off motor. Clean housing and bumper with damp cloth after each use. A little care will keep your Orbiter looking like new. USER MAINTENANCE: Lubrication: The Orbiter motor bearings are factory lubricated and sealed. All other servicing should be performed by an authorized service center. There are no user serviceable parts inside. 3 ENGLISH Troubleshooting Guide WARNING: Unplug cord from electrical outlet before servicing. PROBLEM POSSIBLE SOURCE AREAS TO CHECK FLOOR MACHINE Not plugged in Be sure cleaner is WILL NOT RUN properly. No electricity in wall outlet. Blown fuse/ tripped breaker Motor circuit breaker has tripped. firmly plugged into wall outlet. Check electrical source–fuse or circuit breaker. Replace fuse/ Reset breaker Turn switch off and unplug cleaner. Check motor shaft for binding. Allow 30 minutes for motor to cool and system to reset. If unit is equipped with red reset button, press it. FLOOR MACHINE Brush or pad Place it properly. BOUNCES holder not properly in place. Using brush on dry surface without dry shampoo or wet shampoo. (See operating instructions.) Apply necessary shampoo dry or wet. Whenever calling, please be sure to have your model and serial number from data plate. Accessories (Sold Separately) When choosing different pads and brushes for the Orbiter, there is no exact science to which pad or brush is most suitable on a particular floor. Pads are good for scrubbing and polishing flat surfaces. Brushes work well for getting into recesses in non-flat surfaces, like tile, where the bristles can get into grout lines. When you choose an accessory, remember - you want one aggressive enough to do the job but gentle enough not to damage the floor. Use common sense. For example, do not use a black pad (aggressive) on a wood floor (soft floor). Start with what is safe and move to more aggressive, if needed. The pads are color coded depending on how aggressive they are (except for the beige marble pad): White is the softest, followed by red, green, brown and black being the most aggressive. Pads are designed to be porous and open-weave (except the beige pad) so that when it loosens dirt it can pick it up. The dirt goes inside the pad (i.e. off the floor). All pads can be turned over and the other side used before cleaning and disposing. Pads may be hosed off in some instances and re-used. Brushes are also coded with black being the softest followed by the union mix (tan) brush, the orange scrub brush, with the brown grit brush being the most aggressive. Note: Never store the Orbiter with a pad or brush mounted on it because they can become deformed especially the brushes. DRIVE PADS DRIVE PAD HOLDER (Black plastic with teeth) 53178-51-0327 FLOOR PADS POLISHING PAD (White) 437051 SCRUB PAD (Brown) 437049 STRIP PAD (Black) 437071 BUFFING PAD (Red) 437055 CLEANING PAD (Green) 437056 For all floor pads, place either DRIVE PAD HOLDER or DRIVE PAD BRUSH on Orbiter. Then place the pad on the floor and center Orbiter onto the pad. FLOOR BRUSHES SHAMPOO BRUSH (Black bristle) 237049 Use with ORECK DRY SHAMPOO. This brush has specially cut bristles to provide safe, soft action needed for carpet cleaning. POLISHING BRUSH - UNION MIX (Tan bristles) 237048 This polishing brush can be used to polish wood floors. This brush will “blend” in excess floor wax, maintain an even coat of wax and eliminate wax buildup. SCRUB BRUSH (Orange bristles) 237047 This brush is used to clean ceramic and concrete and many tough stains. GRIT BRUSH (Hard green/gray bristles) 237056 This is an extremely aggressive brush used to scour tough stains on concrete and asphalt. All the floor brushes snap directly onto the Orbiter with no drive pad. Remove the brushes from the machine after use so as not to damage them. OTHER ACCESSORIES LAMBS WOOL BONNET 437054 This bonnet is designed to provide the best possible shine on wood, tile and vinyl floors. To install bonnet, place over the DRIVE PAD HOLDER. Pull the drawstrings tight to prevent slipping. Tie a bow and tuck the excess string inside the bonnet. Use the bonnet for everyday buffing to remove scuff marks. When the bonnet becomes dirty, wash with soap and water, wring it out and place it back on the DRIVE PAD HOLDER to dry to its original shape. WHITE TERRYCLOTH BONNET 437053 This bonnet cleans the traffic lane and spots in the carpet without wetting the entire carpet. When one side of bonnet is dirty, flip it over and use the other side. When bonnet is completely soiled, hose off and air dry. SAND SCREENS The very best in floor sanding. For all sand screens, place either DRIVE PAD HOLDER or DRIVE PAD BRUSH on Orbiter. Then place the sand screen under any floor pad on floor and center Orbiter onto the pad. Th...
Dieses Handbuch ist für folgende Modelle:Schleifmaschinen - Orbiter Multi-Purpose Floor Machine ORB557MC Series (398.25 kb)