Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Festool Dateigröße: 434.91 kb Dateiname: Unterrichtssprache:

Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, • Arsenic and chromium from chemically-treated lumber. The risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals work in a well ventilated area and use approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. Technical data Wattage ............................................ 310 W No load speed ..................6 000 - 10 500 rpm No. of strokes .................12 000 - 21 000 spm Sanding stroke ETS 150/3 EQ ................ 3.0 mm (0.12 in.) ETS 150/5 EQ ................ 5.0 mm (0.20 in.) Sanding base diameter ........ 150 mm (5.9 in.) Weight .................................1.8 kg (4.0 lbs.) Safety level ......................................... / II Symbols V Volts A Amperes Hz Hertz W Watt ~ Alternating current n0 No load speed Class II Construction rpm Revolutions per minute spm Strokes per minute O Diameter Intended use The sanders are designed for sanding wood, plastic, composite materials, paint / varnish, filling material and similar materials. Metal and materials with an asbestos content must not be processed with these tools. The machines must not be damp nor operated in a damp environment for electrical safety reasons. The machines may only be used for dry sanding. The user bears sole responsibility for any damage or accidents resulting from incorrect use. 3 Electrical connec-Electronic control tion and operation You can regulate the speed steplessly between 6000 and 10500 rpm using the adjusting wheel The mains voltage must correspond with the volt( 2.3). This lets you optimize the sanding speed to age on the rating plate! suit the material (see "Working with the tool"). See the following figure for connection and disconnection of the power cable. Dust extraction Always switch the machine off before connecting or disconnecting the power cable! Switch (2.1) is an on/off switch. For continuous use it can be engaged with the lateral locking button (2.2). Pressing the switch again releases the lock. 2.12.2 Extension cord If an extension cord is required, it must have sufficient cross-section to prevent an excessive drop in voltage or overheating. An excessive drop in voltage reduces the output and can lead to failure of the motor. The table below shows you the correct cord diameter as a function of the cord length for the ETS 150/3 EQ, ETS 150/5 EQ. Total Extension Cord Lenght (feed) 25 50 100 150 Cord size (AWG) 18 16 16 14 Use only U.L. and CSA listed extension cords. Never use two extension cords together. Instead, use one long one. Note: The lower the AWG number, the stronger the cord. Tool settings Always remove the power plug from the socket before carrying out any work on the power tool. Dust extractors prevent large accumulations of dust in the air in the working environment and dirt collecting in the workplace. Inboard extraction 3.33.23.13.43.53.63.73.83.9 The machines are fi tted with inbuilt extraction as standard. The sanding dust is extracted through suction openings in the sanding base (3.4) and trapped in the turbo-fi lter (3.2). The turbo-filter has to be changed when it is so full of dust that the extraction power diminishes: –Push the front cardboard section of the turbo- filter with the sealing lip (3.1) onto the extraction nozzle (3.8) of the fi lter holder –Insert rear cardboard section with slot (3.3) onto the retaining strip (3.9) of the fi lter holder – Push the filter holder with its opening (3.6) as far as it will go onto the extraction nozzle (3.5) of the machine and clamp tight by turning rotary knob (3.7). External extraction by an extraction unit 4.1 In order to avoid frequent changing of the turbo- filter when carrying longer sanding jobs, it is possible to connect a Festool extractor to the unit instead of using inbuilt extraction. In this case, the extraction pipe (O 27 mm) (4.1) of the extraction unit is connected to the suction nozzle. 4 Attaching sanding material The appropriate Stickfix sanding paper and Stick- fix sanding felt can be fastened quickly and easily onto the Stickfix sanding base. 5.15.2 The self-adhesive sanding material (5.2) is simply pressed onto the sanding base (5.1) and held safely in place by the Stickfix sanding base velcro surface. Choice and installation of the grinding disks The appliance can be fitted with three grinding disks (5.1) of different hardness depending on the surface to be treated. • Hard: coarse grinding on surfaces, grinding at edges. • Soft: universal for coarse and fine grinding, for flat and curved surfaces. • Super-soft: fine grinding on formed parts, curves, radii. Do not use on edges! The grinding disks and the tool-holding fi xture on the appliance are equipped with a positive holder (6.1). Make sure the grinding disk is correctly positioned before sc...

Herunterladen

Geben Sie zwei Ziffern: