Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Clarke Dateigröße: 822.51 kb Dateiname: Unterrichtssprache:

Refer to the chart to the right for extension cord information. If motor appears to labor or takes a considerable longer time to come up to speed reduce sanding pressure. Figure 1 Feet/Wire Guage (Stranded Copper) Source Voltage 0 - 100' 100 - 250' 208 6Use Voltage Booster 230 10 8 -6-Clarke® American Sanders Operator's Manual (EN) - Floorcrafter ENGLISH EN WARNING: The machine is heavy. Remove the motor from the machine before transporting. Get help loading the machine and motor. Use proper lifting techniques. Transporting the Machine - Using the Dolly Cart CAUTION: When deploying the dolly, the drum will contact the floor or ground over which the machine is resting. Care should be taken to avoid surfaces which might damage or contaminate the drum. CAUTION: While transporting using the dolly, abrupt changes in the direction of travel or the surface over which the machine is being transported could cause the machine to tip over. Also, the machine is more likely to tip over when transporting across inclined surfaces. Attach the dolly to the rear of the machine as follows: 1. Open the quick release levers (2A) and unscrew the adjustment nuts (2B) to allow installation of the dolly. (See figure 2) 2. Insert the quick release skewers into the dolly brackets and immediately tighten the adjustment nuts until the dolly mechanism will just swing free. Deploy the dolly under the machine as follows: 1. With the dolly mechanism in place as described above, tip the machine by lifting up on the operators handle to raise the rear of the machine off the floor/ground until the dolly swings under the machine. (See figure 3) 2. Hold the dolly in position using your foot and allow the machine to tip back and rest on the dolly wheels. (See figure 4) 3. Tip the machine back on all four wheels and close the quick release levers for transport. Some adjustment of the quick release skewers may be necessary to allow the levers to be tightened securely. Removing/Storing the dolly: The dolly can be stored on the machine in the "UP" position or it can be removed and stored separately. 1. Open the quick release levers to loosen the dolly. 2. Lift up on the operators handle to tip the machine forward. 3. Swing the dolly out from under the machine and lower the machine until it rests on its own wheels. How to Transport the Machine AB BA Figure 2 Figure 3 CAUTION: Be careful when lowering the machine. The dolly will swing back toward the operator as the machine Figure 4 is lowered. Clarke® American Sanders Operator's Manual (EN) - Floorcrafter - 7 ENGLISH EN 4. To store the dolly in the "UP" position, swing the dolly up against the top of the mainframe as far as it will travel and close the quick release levers to secure it in place. (See Figure 5) 5. To remove the dolly, loosen the quick release adjustment nuts until the levers and nuts clear the counter-bore on the dolly brackets, and remove the dolly. 6. Tighten the adjustment nuts until the quick release levers can be closed to secure the dolly in place. Transporting the Machine - One Person How to Transport the Machine Figure 5 NOTE: This is accomplished by removing the motor from the chassis and transporting the motor and chassis separately. To transport the machine, follow this procedure: 1. Make sure the power cable is disconnected from the electrical outlet. 2. Release the tension on the drive belts using the quick release lever. (See Figure 6A ) 3. Open the belt guard by pulling on the handle immediately above the left truck wheel. (See Figure 6B) 4. Remove the drive belts from the machine 5. Disconnect the motor pigtail from the handle pigtail. (See Figure 7) if so equipped. 6. Unscrew the motor mounting knobs to loosen the motor. (See Figure 8) 7. Straddle the motor and grasp the motor lift handle. Using your legs, lift the motor off the chassis and take it to the work site. 8. Lift the chassis by grasping the front and rear handles. Lift the frame and bring the belt guard against your chest. Take the chassis to the work site. To assemble the machine after transporting, follow this procedure: 1. Open the belt guard door. Place the motor assembly on the chassis and screw the motor mounting knobs sufficiently to engage and secure the motor. 2. Install the drive belts. Tighten the belts using the belt tension quick release lever. 3. Check the tension on the belts and close the belt guard door. A B Figure 6 Figure 7 Figure 8 -8- Clarke® American Sanders Operator's Manual (EN) - Floorcrafter ENENGLISH How to Transport the Machine ENENGLISH How to Transport the Machine CAUTION: Premature bearing failure can occur if the fan belt is set too tight. The fan belt should deflect ." at the center of the span with 5 lbs. of pressure. NOTE: It is necessary to adjust the fan belt independently during this procedure or during replacement. The idler pulley is factory adjusted. Transporting the Machine by Carrying - Two People 1. Person #1 places his hands under the front of the machine's main c...

Herunterladen

Geben Sie zwei Ziffern: