Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Makita Dateigröße: 163.37 kb Dateiname: Unterrichtssprache:

6. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. Run the tool (with guard) at no load for about a minute, holding tool away from others. If wheel is flawed, it will likely separate during this test. 7. Use only flanges specified for this tool. 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage. 9. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury. 10. Hold the tool firmly. 11. Keep hands away from rotating parts. 12. Make sure cord is clear of wheel. Do not wrap cord around your arm or wrist. If control of tool is lost, cord may become wrapped around you and cause personal injury. 13. Make sure the wheel is not contacting the workpiece before the switch is turned on. 14. Before using the tool on an actual work- piece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. 15. Use the specified surface of the wheel to perform the grinding. 16. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 17. Do not leave the tool running. Operate the tool only when hand-held. 18. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. 19. ALWAYS wear proper apparel including long sleeve shirts, leather gloves and shop aprons to protect skin from contact with hot grindings. 20. Use of this tool to grind or sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION 1 1. Shaft lock 001038 1 2 1. Switch trigger 2. Lock button 001045 1 1. Switch trigger CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock CAUTION: • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when installing or removing accessories. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. For Model 9005B CAUTION: • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. For Model 9005BZ To start the tool, simply pull the switch trigger. Release the switch trigger to stop. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 001055 Installing side grip (handle) CAUTION: • Always be sure that the side grip is installed securely before operation. Screw the side grip securely on the position of the tool as shown in the figure. 001063 Installing or removing wheel guard CAUTION: • When using a depressed center grinding wheel/Multidisc, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Be sure to tighten the screw securely. To remove wheel guard, follow the installation procedure in reverse. 1 2 3 1. Lock nut 2. Depressed center grinding wheel/ Multi-disc 3. Inner flange 001074 Installing or removing depressed center grinding wheel/Multi-disc WARNING: • Always use supplied guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. Mount the inner flange onto the spindle. Fit the wheel/disc on the inner flange and screw the lock nut onto the spindle. 1 2 3 1. Wheel guard 2. Bearing box 3. Screw 1 2 1 2 7 To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the wheel, follow the installation procedure in reverse. 1. Lock nut wrench 2. Shaft lock 001110 Installing or removing abrasive disc (optional accessory) NOTE: • Use sander accessories specified in this manual. These must be purchased separately. Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the lock nut ...

Herunterladen

Geben Sie zwei Ziffern: