Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Makita Dateigröße: 625.38 kb Dateiname: Unterrichtssprache:

To stop the tool from the locked position, pull the trigger fully, then release it. Lock lever CAUTIO N : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15O to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B directions. I WARNING: It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. Continued use of a worn-out wheel may result in wheel explosion and serious personal injury. Depressed center wheel should not be used after it has been worn down to 115 mm (4-1/2") in diameter. Use of the wheel after this point is unsafe and it should be removed from service and rendered unusable by intentional destruction. MAINTENANCE CAUTlON: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the Insulating tip commutator, it will automatically shut off the 7r motor. When this occurs, both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Commutator 1-Carbon brush Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. Brush holder cap To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. @Wheel guard @Depressed center wheel (1 Per pkg) Part No. For Model Part No. Grit Size (mm) For Model 165191-5 9047L 741425-6 24 9047L ,7,!:qr; i 164879-4 I 9049 741421-4 24 ,,,?~~r46~ 9049 I I I @Inner flange 89 @Lock nut 518”-40 (For depressed center wheel) (For depressed center wheel) Part No. 224317-9 Part No. 224509-0 @Rubber pad @Abrasive disc 15 per pkgl Part No. 743012-7 @Sanding lock nut 48 (For abrasive disc) Part No. 224517-1 @Wire cup brush Part No. ~-1I Diameter lmml 743206-A 150 (6") 743206-E @Urethane washer 14 Part No. 261039-0 When using wire brush, mount urethane washer 14 to the spindle. It will make it easier to remove wire brush. @Hubbed grinding wheel Part No. I Grit I Diameter h" 742067-A-5 I 16 1 742069-A-5 I 24 I 742089-A-5 742070-A-5 180 (7") 742071 -A-5 80 742091-A-5 I 120 I @Flexible grinding wheel (10 per pkg) Part No. I Grit I Size lmml I Far Model 18Ox 3 x 22 17" x 118" x 718") 741442-6 I 60 I 9047Llincludes one back up pad,@ w w Part No. 743027-4) 741444-2 120 @Plastic pad Part No. 743027-4 Lock nut wrench 28 Part No. 78241 2-6 Grip 36 Part No. I Grit I Size I For Model Part No. 152539-0 741414-A I A24R I 7"x 114'x 518" I 90471 741 41 5-A A24R 9" x 114" x 518" 9049 No".-01 -'96 US ANGLE GRINDER 180 mm (7") Model 9047L 230 mm (9") Model 9049 Note: The switch and other part configurations may differ from country to country. MODEL 9047L, 9049 Nov.-01-'96 US IFOM DESCRIPTION '2: DESCRIPTION MACHINE -MACHINE 1 1 FIELD ASSEMBLY 25 1 Retaining Ring R-40 2 1 Baffle Plate 26 1 Ball Bearing 62030DW 3 1 Ball Bearing 6200DDW 27 1 Bearing Box 4 1 Insulation Washer 28 1 Spindle 5 1 ARMATURE ASSEMBLY 29 1 Pan Head Screw M8x25 IWith Item 3. 4 & 61 30 1 Wheel Cover 6 1 Fan 80 31 1 Inner Flange 89 7 1 Bearing Retainer 60 32 1 Lock Nut 5/6-40 8 1 Ball Bearing 63OlDDW 33 4 Tapping Screw CT 5x16 9 1 Spiral Bevel Gear 12 34 1 Makila Mark 10 1 Retaining Ring S-9 35 2 Brush Holder Cap 11 4 Tapping Screw. Flange. 5x35 36 2 Carbon Brush 12 1 PI" Cap 37 1 Name Plate 13 1 Compression Spring 12 38 1 Handle Set IWith Item 441 14 1 Hex Socket Head Bolt M5x25 39 1 Cord Guard 15 1 Pin 6 40 1 Cord 16 1 Gear Housing 41 1 Strain Relief 17 1 Grip 36 42 2 Tapping Screw 4x18 18 1 Hex Socket Head Bolt M5x10 43 4 Tapping Screw. Flange. 4x25 19 1 Nut M15-23 44 1 Handle Set IWith Item 381 20 21 22 1 1 1 cup Spring 20 cup Sprrng 20 Lock Washer 45 46 47 1 2 1 Switch Tapping Screw Flange F'T 5x65 Makits Mark 23 1 Spiral Bevel Gear 53 48 1 Motor Housing Complete 24 1-Flat Washer 15 -- Note: The switch and other part specifications may differ from country to country. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leavin...

Herunterladen

Geben Sie zwei Ziffern: