Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Fotos und technische Daten Makita 9403 |
Anleitung Zusammenfassung
2. Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses. 3. Hold the tool firmly with both hands. 4. Make sure the belt is not contacting the workpiece before the switch is turned on. 5. Keep hands away from rotating parts. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. This tool has not been waterproofed, so do not use water on the workpiece surface. 8. Ventilate your work area adequately when you perform sanding operations. 9. Use of this tool to sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS SYMBOLS The followings show the symbols used for tool. V ....................... volts ................alternating current A ....................... amperes ....................Class II Construction Hz ..................... hertz m/s....................meter per second ft/min ................feet per minute FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION 1 2 1. Lock button 2. Switch trigger ASSEMBLY 003370 1 1. Lever CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing abrasive belt Pull the lever all the way out and install the belt over the rollers, then return the lever to the original position. 003375 • When installing the belt, make sure that the direction of the arrow on the back of the belt corresponds to the one on the tool itself. 003379 Adjusting belt tracking While the belt is running, use the adjusting knob to center the belt tracking. Failure to do so can result in frayed belt edges and wear on the sander frame. 1 1. Adjusting knob 003384 Dust bag Attach the dust bag onto the dust spout. The dust spout is tapered. When attaching the dust bag, push it onto the dust spout firmly as far as it will go to prevent it from coming off during operation. 1 2 1. Dust bag 2. Dust spout 003388 When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. NOTE: • If you connect a Makita vacuum cleaner to this tool, more efficient and cleaner operations can be performed. 1 1. Fastener 003390 1 2 3 003390 1 2 3 1. Steel plate 2. Carbon plate 3. Strap washer OPERATION MAINTENANCE 001145 1 1. Limit mark Carbon plate (optional accessory) For greater sanding efficiency and to help the belt run cooler, install an optional carbon plate on the steel plate when sanding hardwood or steel. Sanding operation CAUTION: • The tool should not be in contact with the workpiece surface when you turn the tool on or off. Otherwise a poor sanding finish or damage of the belt may result. Hold the tool firmly with both hands. Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece surface. Keep the belt flush with the workpiece at all times and move the tool back and forth. Never force the tool. The weight of the tool applies adequate pressure. Excessive pressure may cause stalling, overheating of the motor, burning of the workpiece and possible kickback. CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. 003395 2 003395 2 1. Screwdriver 2. Brush holder cap ACCESSORIES Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. CAUTION: • These accessories or attachments are recommended for use with your Makita tool specifie...
Dieses Handbuch ist für folgende Modelle:Schleifmaschinen - 9921 (90.12 kb)