Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
1. After you have put on the appropriate safety gear covered on page 3 of this manual, and you have installed the sanding sleeve you want to use, plug in the Sander. 2. Turn the sander on using the Switch (80). Always run the Sander for a few seconds before contacting the work piece. 3. Contact the work piece with minimal pressure. If the Spindle Sander is not removing enough material, try a coarser grit sanding sleeve. Keep a firm grip on the stock material as you move the stock material into the spinning sanding sleeve. 4. Occasionally check the sanding sleeves for tears, wear, or fraying. Replace if necessary. Stop using if sanding sleeve is damaged. 5. When you are finished, turn off the Switch (80). Remove the yellow Safety Lock and store it out of the reach of children. WARNING! Do not use water with this sander. It is for dry sanding only. Wet sanding will damage the machine, and may present a shock hazard. Use only in dry locations. INSPECTION, MAINTENANCE, AND CLEANING BEFORE EACH USE, inspect the general condition of the Spindle Sander. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. TROUBLESHOOTING 1. Over time, if the performance of the tool diminishes, or it stops working completely, it may be necessary to replace the Carbon Brushes (34) by removing the Brush Holder (33). This procedure should be completed by a qualified technician. If the Carbon Brushes are not worn down, try cleaning the Carbon Brush tips with an ink eraser. 2. If the Sanding Sleeve stops rotating when you touch it or press the stock material against it, turn off the machine at once. Unplug the machine and check to make sure that the Hex Nut (1) is threaded on tight to the Spindle (55). REV10f PARTS LIST 10mm 4.2 x 13 O5 O5 5 x 12 4.2 x 13 4.2 x 13 6203zz 4.2 x 13 4.2 x 22 O6 O6 4.2 x 19 6 x 16 4.2 x 15 6001zz 608zz 4 x 16 O4 4.2 x 13 4.2 x 15 O4 4.2 x 110 4.2 x 10 4.2 x 22 O6 O6 6 x 16 6203zz 4.2 x 13 4.2 x 15 07g PARTS LIST CONTINUED Part Description Q’ty 96 1/2” Throat Plate 1 97 3/4” Throat Plate 1 98 1” Throat Plate 1 99 1-1/2” Throat Plate 1 100 2” Throat Plate 1 101 3” Throat Plate 1 102 1/2 “ Sanding Sleeve (80 grit) 1 103 3/4 “ Sanding Sleeve (80 grit) 1 104 1 “ Sanding Sleeve (80 grit) 1 105 1-1/2 “ Sanding Sleeve (80 grit) 1 106 2 “ Sanding Sleeve (80 grit) 1 107 3 “ Sanding Sleeve (80 grit) 1 108 3/4” Rubber Spindle 1 109 1” Rubber Spindle 1 110 1-1/2” Rubber Spindle 1 111 2” Rubber Spindle 1 112 3” Rubber Spindle 1 113 5/8” OD Spindle Washer 1 114 7/8” OD Spindle Washer 1 115 1-3/4” OD Spindle Washer 1 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. REV 07d ASSEMBLY DIAGRAM 5 (96, 97, 98, 99, 100, 101) 4 (108, 109, 110, 111,112) 3 (102, 103, 104, 105, 106, 107) 2 (113,114,115) REV 07d, 07i ASSEMBLY DIAGRAM CONTINUED 96 97 98 100 101 99 102 107 106 105 103 104 112 111 110 109 108 Limited 1 year / 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all other parts and components of the product are free from defects in materials and workmanship (90 days if used by a professional contractor or if used as rental equipment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide yo...