Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This will clean the surface, leave no residue and assure a secure bond. Pressing Magnetic Switch ON will 5. start the Sander. OFF will stop the Sander. When using the Disc Sander, always 6. use the LEFT side of the sanding disc (as you face it) to sand. The sanding disc turns counterclockwise and using the right side could cause kickback. Use two hands and hold workpiece 7. securely at all times. Always maintain a maximum of 1/16” 8. clearance between the Table (69) and sanding disc. When finished with Belt/Disc Sander, 9. to prevent accidents, turn off and disconnect its power supply after use. Remove the Orange Plastic Key from the Magnetic Switch (31). Wipe down and store the Sander indoors out of children’s reach. Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication BEFORE EACH USE,1. inspect the general condition of the Belt/Disc Sander. Check for loose screws, misalignment or binding of moving parts, cracks and any other condition that may affect its safe operation. A Dust Port (59) is located on 2. the bottom of the Lower Guard Plate (60). It held in place with Screw (61) and can be removed for vacuuming collected dust and sanding residue. Replace the Dust WARNING Port (59) after cleaning and tighten Screw (61). After Use,3. clean external surfaces of the tool with clean cloth. Periodically recheck all nuts, bolts 4. and screws for tightness. Apply a light coat of paste wax to the 5. Table (69) to make feeding material easier. Use compressed air to blow dust and 6. debris from the Sander and Motor. The Bearings on this Sander are 7. sealed and do not require lubrication. Sanding Belt Replacement Push the Belt Tensioner Handle (50) 1. forward to loosen the belt. Remove Upper Guard Plate (58) by 2. unscrewing four Screws (7). Remove the Lower Guard Plate 3. (60) by unscrewing the four Screws (7) that hold it to the Belt Support Housing (52). Slide the old sanding belt off the Rear 4. Roller (56) and Front Roller (44). Replace with a 4” X 36” sanding belt 5. with the correct grit for the project you are working on. NOTE: The larger the grit number, the smaller the grain. Use small numbered grits for cutting and larger for smoothing and finishing. Slide new sanding belt onto Front 6. and Rear Rollers. Replace the Lower Guard Plate 7. (60) and tighten the four Screws (7) securely. Replace the Upper Guard Plate (58) 8. and tighten the four Screws (7). Push the Belt Tensioner Handle (50) 9. to the rear to tighten the belt. Before using, manually check 10. the new belt for alignment. See instructions in the “General Operating” section of this manual. V-Belt Replacement Remove Set Screws (6) and pull off 1. Aluminum Disc (5). Remove four Screws (11) and 2. Washers (10) from Outer Pulley Cover (9). Once the Outer Pulley Cover (9) is 3. removed, the V-Belt is accessible. Remove the V-Belt (12) using a 4. small straight slot screwdriver (not supplied). Place the tip of the screwdriver between the Motor Pulley (13) and the V-Belt (12) while you manually turn the V-Belt by hand. As it turns, the V-Belt will ride up and out of the Pulley groove. Once off the Motor Pulley (13), lift it off of the Spindle Pulley (14). Place the new V-Belt (12) onto 5. the Spindle Pulley (14), by using a straight slot screwdriver (not supplied) as a wedge, manually turn the Spindle Pully (14) and ride the new V-Belt onto the Motor Pulley (13). Replace Outer Pulley Cover (9). 6. Tighten Screws and Washers (10 & 11). 7. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. V-Belt Replacement V-Belt Tensioning Should the V-belt need tensioning, repeat steps 1 and 2, in V-belt Replacement section mentioned previously. L1. oosen four Motor Mount Nuts (22) and slide the Motor (40) further forward towards Front Roller (44), making sure to pull evenly on the motor. While holding the motor in its current position, tighten the Nuts (22). Place a straight edge on the faces of the two pulleys to ascertain alignment. 2. Contact surfaces of the pulleys and the straight edge shall fully touch. Fully tighten the Nuts (22). Repeat steps 2 and 1 in the V-Belt Replacement section.3. Troubleshooting Problem Possible Causes Likely Solutions Belt/Disc Sander does not turn on Not plugged in.1. No power at outlet.2. Orange Plastic Key not inserted 3. into Magnetic Switch (31). Switch is not turned “ON”.4. Plug in Sander.1. Check power at outlet and/or circuit breaker.2. Insert Orange Plastic Key into ...