Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn On and Off properly. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the Sander. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. Compressed air only. Use clean, dry regulated, compressed air at 90 PSI. Do not exceed max. 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Setup Recommended Air Line ComponentsPalm Grip SanderAir CompressorFor best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. Note: If you are not using an automatic oiler system, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of continual use. You will need to prepare a 1/4” male air connector (not included) to be attached to the Inlet Connector on the Palm Grip Sander. Wrap the 1/4” air connector with pipe thread seal tape before threading it into the Inlet. Connect the 3/8” ID Air Hose to a quick connect coupler (not included), and then to the Sander. Set the air pressure on the regulator to 90 PSI. Do not exceed the recommended air pressure of 90 PSI. Check the air connection for leaks. assembly Installing the Sanding Pad Disconnect the air hose from the tool. Select the appropriate Sanding Pad (not included), and press it onto the Backing Pad (41). Firmly press the Sanding Pad onto the Backing Pad (41), making certain it is securely in place. Failure to properly secure the Sanding Pad may cause the Sanding Pad to come loose, possibly causing personal injury or property damage. Installing the Backing Pad Disconnect tool from air supply. Slide Wrench (39) under Cover (37) and onto the Tilting Axle (or Arbor) (28). Holding the Wrench firmly, rotate Tilting Axle (28) counterclockwise to remove. To replace the Backing Pad (41), place Wrench (39) onto Tilting Axle (28) and hold firmly. Place Backing Pad (41) onto Tilting Axle and turn clockwise to attach. Hand tighten firmly. operation Turn the air compressor (not included) on and allow the air tank to come up to pressure. Set the compressor output regulator to no more than 90 PSI. Attach the air supply hose (not included) to the tool. Grip the base of the tool in one hand. The Trigger (1) will be under your palm. Squeeze the tool to depress the Trigger (1) and the tool will operate. Place the tool on the work surface to begin sanding. To stop sanding, lift the tool from the work surface, and relax your grip to allow the Trigger (1) to lift into the OFF position. When you are done work, disconnect the air pressure hose from the tool and turn off the air compressor. REV 07h Inspection, Maintenance and cleaning Make sure your Palm Grip Sander is disconnected from the air hose before attempting any maintenance. Wipe the Palm Grip Sander down with a lint free cloth after each use. If you do not use an inline oiler/filter system, lubricate the tool...