Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by “WA” on the jacket). Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. There are certain applications for which this tool was designed. This tool shall not be modified and/or used for any application other than which it was designed. All accessories must be rated for at least the RPM speed recommended on the tool’s warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. For safe operation, only these accessories can be used with this product: Abrasive Cut-Off Discs and Wheels Flap Wheels Wire Brushes Wire Wheel Brushes Always use an approved and proper guard when using the above mentioned accessories. Each accessory must have the correct arbor size and must fit properly on the shoulder bushing. Make sure accessories are tightened down securely. NEVER INSTALL A CIRCULAR SAW BLADE FOR USE ON THIS ANGLE GRINDER. NEVER INSTALL A WOOD CARVING BLADE, CARVING DISC WITH SAW CHAIN CUTTERS, OR A CUTTING CARVING DISC ON THIS ANGLE GRINDER. Warning! Always use an approved and proper guard when using the recommended accessories (listed on page 5). Each accessory must have the correct arbor size and must fit properly on the shoulder bushing. Make sure accessories tightened down securely. Never install a carbide tipped or steel circular saw blade for use on this Angle Grinder. Never install a wood carving blade, carving disc with saw chain cutters, or cutting-carving disc. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Note: Performance of this tool (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly Warning! Make sure the unit is unplugged before assembling, or when changing discs. Screw the threaded end of the Side Handle (18) into the threaded hole to the right of the Gear Box (17). See Assembly Drawing. With one hand, hold the body of the Grinder while depressing the Stop Pin (1). With the other hand, insert the two tabs on the Wrench (56) into the holes on the Flange Nut (35). Loosen the Flange Nut (35) by turning it counterclockwise. Remove the Flange Nut (35). Place the Wheel (34) over the Spindle (30) and onto the Flange (33). Replace the Flange Nut (35) by turning it clockwise. The Angle Grinder is ready for use. Operation Note: For safe operation, only these accessories can be used with this product: 4-1/2” diameter Grinding Wheel (included with this product), Abrasive Cutoff Discs, Flap Wheels, Wire Brushes, and Wire Wheel Brushes. Plug in the Cord Plug (55). Firmly grasp the Side Handle (18) with one hand, and the body with the other. Make sure the Protecting Cover (32) is between you and the grinding wheel. If necessary, turn off the Grinder, unplug it, and rotate the Protecting Cover (32). For grinding or cutting, approach your workpiece at an angle between 15 and 30 degrees. Remember to let the wheel do the work. Do not force it or put too much pressure on the Grinder. Caution: Always be alert to the possibility of kickback. Always firmly hold tool with both hands. Slide the Switch (50) until it locks on. To turn it off, just press down on the Switch (50) and it will unlock. REV 03e Maintenance Periodically blow out motor vents with compressed air. Clean plastic with a damp cloth. Never use solvents. No lubrication required. If performance lacks, change the Carbon Brush (44). Using a screwdriver, unscrew the Brush Cap (45). Remove the Brush (44) from the Brush Holder (43). Replace with an identical replacement part from Harbor Freight Tools. Replace Brush Holder (43) and Brush Cap (45). LIMITED 90 DAY WARRANTY H...