Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Delta
Dateigröße: 485.74 kb
Dateiname: bee94dd9-ace4-4225-ab76-2dcda1cbea4f.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
10-24x3/8" Pan Head Screw (2) 10. M8.4 Flat Washer (1) 11. 3/16" Flat Washer (2) Fig. 1 1 2 3 4 5 6 7 8 9 12 13 5 ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. BELT SANDER TABLE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Locate the M8x1.25x30mm hex head screw (A) Fig. 2, M8.4 flat washer (B), and table locking handle assembly (C), (D), (E) and (F). NOTE: The table locking assembly (C, D, E, and F) is shipped assembled. For ease in assembling table to sander, remove screw (F), spring (E), and handle (D) from locking stud (C). 3. Place table (G) Fig. 3, on sander by inserting belt (H) and platen (I) through opening (J) in table, as shown. 4. Insert M8x1.25x30mm hex head screw (A) Fig. 4, into hole in sander frame and through slot (K) underneath table and fasten using M8.4 flat washer and stud (C), tighten the stud (C) hand tight. 5. The M8.4 flat washer (B) and stud (C) are also shown in Fig. 5. Place handle (D) on end of stud and fasten in place using spring (E) and screw (F) Fig. 5. 6. The table (A) is shown completely assembled to the sander in Fig. 6. NOTE: The locking handle (B) is spring loaded and can be repositioned by pulling out the handle and repositioning it on the serrations located underneath Fig. 3 the handle. WARNING: To avoid trapping the workpiece or your fingers between the table (A) and the sanding belt (D), adjust the table so that there is a maximum 1/16" between the work table and the belt (see the section “BELT TABLE ADJUSTMENTS”). ABCDEF G Fig. 2 G HI J A K C Fig. 4 B C D EF A BC D Fig. 5 Fig. 6 6 A B Fig. 7 A B Fig. 8 ABRASIVE TO SANDING DISC 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove one-half of the abrasive backing (A) Fig. 7, to expose the adhesive. 3. Attach the lower section of the abrasive to the sanding disc (B), making sure that the abrasive edges fit the sanding disc edges exactly. 4. Remove the other half of the abrasive backing. Fig. 9 5. Attach the upper edge of the abrasive backing to the sanding disc. Press the entire abrasive to be certain that it is attached solidly to the sanding disc. SANDING DISC GUARD AND TABLE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Position the sanding disc guard with table (A) Fig. 8, over sanding disc (B). 3. Fasten the sanding disc guard with table (A) Fig. 9, to base using the two 10-24x3/8" pan head screws, and Fig. 10 3/16" flat washers, one of which is shown at (B). WARNING: To avoid trapping the workpiece or your fingers between the table (A) and the sanding disc (B), adjust the table so that there is a maximum 1/16" between the work table and the disc (see the section “DISC TABLE ADJUSTMENTS”). FASTENING SANDER TO SUPPORTING SURFACE IMPORTANT: If the machine has a tendency to tip over or to walk on the supporting surface, the machine must be secured. Use the four holes, three of which are shown at (A) fig. 11 to attach the machine to the supporting surface. Fig. 11 A B A BC AA 7 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING SANDER The switch (A) Fig. 15 is located on the top of the switch box. To start the sander, move the switch forward to the “ON” position. To stop the sander, move the switch back to the “OFF” position. A Fig. 15 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the tool is not in use, the switch should be locked in the OFF position using a padlock (B) Fig. 16, with a 3/16" diameter shackle to prevent unauthorized use. TRACKING THE BELT The belt tracking adjustment is set at the factory so that the abrasive belt will run true on the pulleys. If, however, the belt should lead to either side of the pulleys, make the adjustment by turning the tracking knob (A) Fig. 17. Turning the knob (A) clockwise (when facing the sander) will move the belt to the right. Turning the knob (A) counterclockwise will move the belt to the left. BELT TABLE ADJUSTMENTS For most sanding operations, set the table at a 90 degree angle to the sanding belt. A 90-degree positive stop is provided with your sander to ensure fast positioning of the table. Adjust the positive stop as follows: 1. Loosen the table locking lever and tilt the table to the rear as far as possible. 2. Place a combination square on the table with the 90 degree end against the sanding belt, (Fig. 18), to confirm that the table is 90 degrees to the belt. 3. If this is not the case, turn adjusting screw (A) with wrench (B) Fig. 18, until the angle is correct. B Fig. 16 A Fig. 17 A B Fig. 18 8 4. The table can be tilted to the front (Fig. 19), by loosening table locking handle (C), tilting the table to the desired angle and tightening the table locking handle (C). 5. The table can be adjusted in or out by loosening the table locking handle and moving the table in or out. Retighten lock handle when the adjustment has been made. WARNING: To avoid trapping the workpiece or your fingers between the table (D) and the sa...