Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
The load meter and the variable speed dial are very important to the operation of the Model G1066Z. Please read the “Load Meter” and the “Variable Speed” instructions in this section before sanding any stock. Test Run Once the assembly is complete and the adjustments are done to your satisfaction, you are ready to test the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your finger is poised on the STOP button, just in case there is a problem. The drum sander should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises should be investigated and corrected before operating the machine further. To avoid injury or damage to the machine, DO NOT attempt to make adjustments to the machine without turning it off and unplugging it from its power source. If noises occur that cannot be found by visual inspection, feel free to contact our Service Department for help. G1066/G1079 Your new Model G1066/G1079 Drum Sander is a relatively simple piece of equipment to set up and run. Under most sanding conditions, a normal cut is no more than 1.64". This depth can be achieved by approximately 1.4 turn of the table height handle. Attempts to remove too much can cause jamming, wood burning, rapid paper wear or tearing, poor finish and belt slippage. We recommend that wide stock be sent through two to three times without adjusting the table height. Turn the stock 180° to ensure an even cut. The following is the correct start-up and operating procedure for either of these machines. 1. Start the dust collector. 2. Make thickness adjustment. Place workpiece on the conveyor table and turn the table handle until the workpiece can be sanded and fed through smoothly. Turning the handle clockwise will raise the conveyor table. Turning the table handle counter-clockwise will lower the conveyor table. 3. Remove the workpiece from the conveyor belt. 4. Start the Drum Sander and feed your stock. Retrieve by standing at the side–not at the outfeed end. 5. Check the sanded piece. Is the piece smooth? Mark a squiggly pencil line on a board and sand it to test for even sanding. Look for uniform removal of the line. If the line is not removed uniformly, refer to the adjustment section earlier in the instruction manual. NOTICE We strongly recommend sending wide stock through the sander two or three times without adjusting the height. This is an important method for preventing burning your wood or ruining sandpaper. DO NOT attempt to investigate or adjust any features of the machine while it is running. Wait until the machine is turned off, unplugged and all working parts have come to a rest before you do anything! Failure to do so could result in severe injury or damage to equipment. DO NOT sand more than one board at a time. Minor variations in thickness can cause one board to be propelled by the rapidly spinning sanding drum and ejected from the machine. NEVER stand directly in front of the outfeed area of the machine. Failure to do so could result in severe personal injury. G1066/G1066Z/G1079 Drum Sander -23 G1066Z Your new Model G1066Z Drum Sander provides a great amount of operator control during operation. To utilize this control, you should be familiar with the variable speed and the load meter before using the drum sander. Variable Speed The variable speed dial located on the control panel allows you to increase the feed rate from 020 FPM. The correct speed to use depends on the type of stock you are using (hardwood vs. softwood) and the stage of finish you are at with that stock. As a general rule, a slower feed rate will sand the surface smoother, but runs the risk of burning the wood; a faster feed rate will remove material faster, but runs the risk of overloading the motor. Use trial-and-error to determine the best settings for your specific applications. Load Meter The load meter located on the control panel displays the current amperage draw of the drum motor. The needle rises when you increase the load on the sanding drums and decreases when you decrease the load. Use this meter to avoid overloading your machine with too heavy of a cut. NEVER exceed 25 amps—this is the maximum that your machine can safely handle! Since various types of stock will react differently with various loads, use trial-and-error to determine the best settings for your applications. As a general rule, always start with a small load and work your way up. We recommend that you do not push your machine to its maximum load; instead, make multiple passes or install a coarser grit paper. Operation Under most sanding conditions, a normal cut is no more than 1.64". This depth can be achieved by approximately 1.4 turn of the handle. Excessively heavy cuts can cause jamming, wood burning, rapid paper wear, poor finish and belt slippage. We recommend that wide stock be sent through two to three times without adjusting the table height—this is important for preventing burned wood or ruined s...
Dieses Handbuch ist für folgende Modelle:Schleifmaschinen - G1079 (4.33 mb)