Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
All adjustments or repairs must be done with the sander disconnected from the power source, unplugged. Failure to comply may result in serious injury! The PDS-12CS disc sander is rated 115V/230V, Prewired 115V. If you want to run the PDS-12CS on 230V refer to the wiring diagram found on the inside of the switch box cover (I, Fig. 8). Before hooking up to the power source, make sure that the switch is in the off position. 11 Emptying the Collector Bag Optional Accessories .. CAUTION Wearing a particle mask/respirator for protection against fine dust particles during cleaning is highly recommended. During first use and after cleaning, the bag may allow some dust to escape. This is normal and will stop after a short period of time. Clean the collector bag frequently to keep the collector's performance at its optimum. To clean: 1. Disconnect the machine from the power source, unplug. 2. Remove the collector bag from the hanger rods. 3. Loosen the ring clamp and remove the bag. 4. Empty the contents into an appropriate container. The bag is easily emptied by unzipping the bottom of the bag. 57620025: JET Stik Abrasive Belt and Disc Cleaner. JDS-12B Sanding Disc PSA Aluminum Oxide “J” Weight Cloth Back. 12” 36 Grit 50 Grit 60 Grit Stock Number 57698525 57698650 57698750 Master Carton 25 50 50 12” 80 Grit 100 Grit 120 Grit Stock Number 57698850 57698950 57699050 Master Carton 50 50 50 Troubleshooting Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord Sanding disc does not come up to speed 1. Extension cord too light or too long 2. Low current 1. Replace with adequate size and length cord 2. Contact a qualified electrician Machine vibrates excessively 1. Stand or base on uneven surface 1. Adjust stand or base so that it rests evenly on the floor 2. Bolt down Sanded edge not square 1. Table not square to sanding disc 1. Use a square to adjust table to sanding disc Sanding marks on wood 1. Work held still 2. Wrong grit sanding disc 3. Feed pressure too great 4. Sanding against the grain 1. Keep workpiece moving 2. Use coarser grit for stock removal and fine grit for finish sanding. 3. Never force workpiece 4. Sand with the grain 12 Base Assembly Breakdown 13 Parts List for the PDS-12CS Base Assembly Index Part No. No. Description Size Qty 1..........612083......................... Closed Stand......................................... ...............................................1 2..........612097......................... Door w/Latch Assembly ......................... ...............................................1 3..........150503......................... Latch Assembly..................................... ...............................................1 4..........150503-1...................... Spacer................................................... ...............................................2 5..........SP040100....................Pan Head Bolt.......................................M4 x 5.....................................2 6..........331003......................... Impeller.................................................10” ..........................................1 7..........410030......................... Gasket................................................... ...............................................1 8..........SH080402....................Hex Head Bolt.......................................M8 x 20 (LH)...........................1 9..........TS-1551061................. Lock Washer .........................................M8 ..........................................1 10........TS-1550061................. Flat Washer...........................................M8 x 30...................................1 11........612088......................... Cover .................................................... ...............................................1 12........SG069300.................... Hex Flange Bolt.....................................M6 x 12...................................8 13........612089......................... Bearing Housing.................................... ...............................................1 14........TS-1551041................. Lock Washer .........................................M6 ..........................................3 15........TS-1482031................. Cap Screw.............................................M6 x 16...................................3 16........612112......................... Bushing ................................................. ...............................................1 17........BB-6204LLU ................ Ball Bearing...........................................6204LLU .................................2 18........RR470000.................... Retaining Ring.......................................R47.........................................1 ...