Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Hitachi Dateigröße: 258.6 kb Dateiname: 6c2ecccc-ecd9-422d-8120-fc5fc5007b67.pdf Unterrichtssprache:

2). English POLISHER OPERATION 1. Hold the polisher firmly by its housing and side handle (Fig. 1). The polisher produces a counterforce which must be controlled by firmly holding onto the polisher. 2. Switch operation This enables the polisher always to be controlled with the hand gripping the machine for maximum safety during polishing operations. Switch ON: Press the switch trigger. Switch OFF: Release the switch trigger. Switch ON: Press the switch trigger. The switch trigger is locked by pushing on the locking button. Switch OFF: Press and release the switch trigger. 3. Use light polishing pressure. There is no need to press hard when polishing. Usually the polisher’s own weight is sufficient to allow the required light contact with the surface to be ground. CAUTION: Do not press the polisher forcibly against the surface to be ground. Heavy pressure can damage the surface being ground or damage the polisher’s motor. 4. Use of polishing compound or wax Depending on the finishing degree of the surface, use the polishing compound or wax. In order to attain the maximum polishing effect, first polish the surface with the fine sand paper using the sander, then polish it with the polishing compound using the wool bonnet, and then finish with wax. Apply a small quantity of the compound and wax to the surface, and polish with the wool bonnet. 5. Beware of the cord during operation CAUTION: Do not let the cord touch the wool bonnet during its operation, for the rotating wool bonnet may catch the cord and roll it in. 6. Precaution after use CAUTION: Do not lay the polisher down immediately after using on a place where there are many shavings, much dirt and dust until it has completely stopped revolving. If the polisher is laid down with the wool bonnet turned downward before it has completely stopped revolving, there is a risk that the material may be damaged and the polisher may run wild, resulting in injury. English WOOL BONNET ASSEMBLY AND DISASSEMBLY WARNING: Never attempt to assemble or disassemble the wool bonnet while the polisher is capable of being turned “ON”. Be sure power switch is in the “OFF” position and the electrical cord has been disconnected from the receptacle. 1. Assembling (Fig. 2) (1) Turn the polisher upsidedown so that the spindle is facing upward. (2) Insert the washer nut through the rubber pad and thread it onto the spindle. (3) Press the lock lever to secure the spindle and tighten the washer nut with a wrench. (4) Wrap the rubber pad with the hood of the wool bonnet and firmly secure it by tying a string around it. Be sure the excess string is firmly tucked inside the wool bonnet to prevent it from flying out while polishing. The unbalanced fitting of the wool bonnet may cause the vibration (Fig. 3). CAUTION: . Improper fitting of the wool bonnet may cause vibration. . Tighten the washer nut securely and confirm that the rubber pad does not wobble. . After releasing the lock lever, check to be sure that it has returned to its normal position. 2. Disassembling To remove the wool bonnet, follow the above-mentioned procedure in reverse order. Wool Bonnet Wrench Washer Nut Rubber Pad Tighten Fig. 2 Spindle Lock Lever Wool Bonnet Fig. 3 English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately. WARNING: Using this polisher with loosened screws is extremely dangerous. 2. Confirm that there is no damage in the cord and the housing, etc. Furthermore, confirm that there is no abnormality in No. of carbon the activation of the switch. Wear limit brush 3. Inspecting the carbon brushes (Fig. 4) The motor employs carbon brushes which are consumable parts. Replace the carbon brush with a new one when it becomes worn to its wear limit. 0.24” (6 mm) Always keep carbon brushes clean and ensure that they slide freely within the brush holders. 0.67” (17 mm) 43 CAUTION: Using this polisher with a carbon brush which is worn in excess of the wear limit Fig. 4 will damage the motor. NOTE: Use HITACHI carbon brush No. 43 indicated in Fig. 4. . Replacing carbon brushes: Remove the brush caps (Fig. 1) with a slotted screwdriver. The carbon brushes can then be easily removed. 4. Service and repairs All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY. English ACCESSORIES WARNING: Never use any accessories other than those mentioned below. The use of any other attachment or accessory can be dangerous and could cause injury or property damage. NOTE: Accessories are subject to change without any obli...

Herunterladen

Geben Sie zwei Ziffern: