Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. Grinding wheels or any other accessory must have a maximum safe operating speed greater than the “no load RPM” marked on the tool’s nameplate. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. -3 SM 2610947884 06-07 6/5/07 10:45 AM Page 4 SM 2610947884 06-07 6/5/07 10:45 AM Page 4 Always use auxiliary handle for maximum Position the cord clear of the spinning control over torque reaction or kick-back. grinding wheel or any other sanding Operation of the grinder without the side accessory. Do not wrap the cord around handle could cause loss of control of the your arm or wrist. If you lose control and grinder, resulting in possible serious personal have the cord wrapped around your arm or injury. wrist it may entrap you and cause injury. Never leave the tool locked "ON". Before Avoid bouncing and snagging the wheel, plugging the tool in, check that the switch especially when working corners, sharp is "OFF". Accidental start-ups could cause edges etc. This can cause loss of control injury. and kick-back. Be aware of the location and setting of the Regularily clean the tool’s air vents by switch buttons. If the switch is locked "ON" compressed air. Excessive accumulation of during the use, be ready for emergency powdered metal inside the motor housing situations to switch it "OFF". may cause electrical failures. Before using a grinder or installing a new Do not grind or sand near flammable wheel, inspect the grinding wheel for materials. Sparks from the wheel could chips and cracks. Remove bad wheels ignite these materials. immediately. Run the tool at no load for This tool can be converted to a sander. one minute, holding the tool in the When grinding is resumed the proper direction away from people. Wheels with guard and wheel flanges MUST be flaws will normally break apart during this reinstalled before proceeding with time. grinding. The guard must always be Carefully handle both the tool and attached to the tool and positioned for individual grinding wheels to avoid maximum safety, so the least amount of chipping or cracking. Install a new wheel wheel is exposed from the side the tool is if tool is dropped while grinding. Do not being operated. The grinding wheel guard use a wheel that may be damaged. cannot be used for most sanding operations Fragments from a wheel that bursts during or for wire brushing. operation will fly away at great velocity When sanding, do not use oversized possibly striking you or bystanders. sanding disc. Larger sanding disc will Do not use grinding wheel that is larger extend beyond the sanding pad causing than the maximum recommended size for snagging, tearing of the disc or kick-back. your tool, or worn down damaged wheels Extra paper extending beyond the sanding from larger grinders. Wheels intended for pad can also cause serious lacerations. large angle sander/grinders are not suitable !WARNING Some dust created by for the high speed of a small angle power sanding, sawing, sander/grinder, these wheels may easily grinding, drilling, and other construction burst and the fragments strike you or activities contains chemicals known to bystanders. cause cancer, birth defects or other Do not use depressed hub grinding reproductive harm. Some examples of wheels for cut-off operations. Depressed these chemicals are: hub wheels or type 27 wheels are not • Lead from lead-based paints, intended for side loading and may shatter • Crystalline silica from bricks and cement under overload. and other masonry products, and Do not use this tool with “Woodcarving” • Arsenic and chromium from chemically- blade. Such blades create frequent kick-back treated lumber. and loss of control. Your risk from these exposures varies, Wear proper apparel while using a depending on how often you do this type of sander/grinder. Face shield or at least work. To reduce your exposure to these safety goggles, dust mask, leather gloves chemicals: work in a well ventilated area, and and shop apron capable of stopping small work with approved safety equipment, such wheel or workpiece fragments. as those dust masks that are specially designed to filter out microscopic particles. -4 SM 2610947884 06-07 6/5/07 10:45 AM Page 5 SM 2610947884 06-07 6/5/07 10:45 AM Page 5 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name...