MULTI-TASKER MANUAL PART NUMBER: 400-0092-005 MT104-102 6-IN, 1-OUT VGA SWITCHER CARD FOR MULTI-TASKERTM ENCLOSURES USER’S GUIDE MULTI-TASKER TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS...............2 GENERAL..........................................................2 INSTALLATION .................................................2 CLEANING ........................................................2 FCC / CE NOTICE.............................................2 ABOUT YOUR MT104-102 .......

Cable Lengths Note: Measurements made using ALTINEX low-skew cable, CB3150PV. VGA: 640x480@60Hz 900 ft (274 m) XGA: 1024x768@60Hz 700 ft (213 m) SXGA: 1280x1024@60Hz 650 ft (198 m) UXGA: 1600x1200@60Hz 600 ft (183 m) Table 1. MT107-303 General MECHANICAL MT107-303 Enclosure Slots Required 1 Weight 0.4 lb (0.18 kg) Connector Panel Black Anodized T° Operating 10°C-50°C T° Maximum 75°C Humidity 90% non-condensing MTBF (calc.) 38,000 hrs Table 2. MT107-303 Mechanical 400-0372-005 3 MULTITASKER ELECT

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • Any changes or modifications to the unit not expressly approved by ALTINEX, Inc. could void the user’s authority to operate the equipment. 400-0378-004 2 SWITCHER ABOUT YOUR SW1956CT 2 TECHNICAL SPECIFICATIONS 3 SW1956CT 2-In, 1 Out Twisted Pair Auto-Switcher The SW1956CT is a 2-In, 1-Out Twisted Pair Auto-Switcher. Th

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions found herein, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense. • Any changes or modifications to the unit not expressly approved by ALTINEX, Inc. could void the user’s authority to

Model No. Description TABLE MOUNT HARDWARE TM1276 Table Mount bracket for 2U . Rack- Wide RACK MOUNTING ACCESSORIES DA1298RM Rack mount shelf for two units side by side DA1299RM Rack ears for single unit. CONTROL CABLES RC5204CC Contact Closure Adapter 6 ft RC5207CC Master-Slave Control cable HIGH RESOLUTION VGA CABLE CB3703MR 3 feet VGA Male to Male CB3706MR 6 feet VGA Male to Male CB3715MR 15 feet VGA Male to Male CB3725MR 25 feet VGA Male to Male CB3750MR 50 feet VGA Male to Male CB3775MR 75

It is equal to the enclosure slot number in which the card is installed. The value can range from 1 to 4 up to 1 to 20 depending on the enclosure. Card ID 0 (C0) is used for the controller. See the MT100-100 User’s Guide for details. The Group ID is a number representing a group of cards defined with the [WR] command. When using the Group ID, all cards in the group will perform the given instruction. Changing the position of a card will significantly affect the commands recorded on software defi

Step 8. Please adjust the Horizontal position of the image as described in Section 4.5. If your computer and display device are turned on and you see a good clear image, you have successfully interfaced your computer with the video display. CONGRATULATIONS! YOU ARE DONE. If you experience any problems, please call 1-800-258- 4623 or 1-714-990-2300 for international calls. OPERATION 7 The settings of the VA6831FC Interface can be adjusted using the dip-switches in Table 4. There are no other adju

Using this command, the user may also operate the switcher manually. n = ON/OFF switch n = 1 (turns auto switcher ON) n = 0 (turns auto switcher OFF) Example: Sending the [OAS1] command will set the auto switch feature to the ON position to detect the incoming video signal automatically. 9. [0I#] - Change Identification Number This command sets a unique ID number to each MX2456RM Switcher being used. A maximum of 9 unit ID’s can be assigned. 0 = Zero # = New switcher module ID number. (no. from

TNP502 General MECHANICAL TNP500/502 Width (inches) 6.03in (153mm) Height (closed) 4.79in (122mm) Height (opened) 8.05in (205mm) Depth (inches) 7.56in (192mm) Finish Flat Black T° Operating 10°C-45°C T° Maximum 60°C Humidity 90% non-condensing Table 2. TNP500/502 Mechanical ELECTRICAL TNP502 Power Power Rating (pass through connector) 90-140 VAC, 5Amps Max Table 3. TNP502 Electrical 3 TNP500/502 DIMENSIONS 4 TNP500/502 DIMENSIONS 4 ACCESSORIES Detailed dimensions, tabletop cutout templates and C

2 GENERAL..........................................................2 HANDLING ........................................................2 CLEANING.........................................................2 FCC NOTICE .....................................................2 ABOUT YOUR MT110-103....................................... 3 TECHNICAL SPECIFICATIONS.............................. 3 PRODUCT DESCRIPTION ...................................... 4 APPLICATION DIAGRAMS...............................