Government will receive no greater than Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any technical data. User’s Guide 5964-7333 Printing Copies of Documentation from the Web To print copies of documentation from the Web, download the PDF file from the Agilent web site: •Go to • Enter the product model number

• Enter the product model number in the Search function and click Search. •Click on the Manuals hyperlink. • Open the PDF of your choice and print the document. Contacting Agilent Assistance with test and measurements needs and information on finding a local Agilent office are available on the Web at: If you do not have access to the Internet, please contact your Agilent field engineer. NOTE In any correspondence or telephone conversation, refer to the Agilent product by its model number and ful

The Windows® based software runs on a PC that interfaces with an Agilent digital RF receiver and with cdmaOne, cdma2000, HSDPA, UMTS, GSM, GPRS, EDGE, and iDEN phones. The system can be configured to include receivers and phones from one or a combination of technologies simultaneously. The system can control up to four phones. The Agilent E6474A system requires a PC. The PC requirements differ depending on the hardware configuration and on which parameters are being selected. Minimum PC specific

Agilent Technologies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Microsoft®, Windows®, Windows NT® are U.S. registered trademarks of Microsoft Corporation. NI-488.2 is a trademark of National Instruments Corporation. © Copyright 1999 - 2012 Agilent Technologies Agilent Technologies Firmware Upgrade Kits E4400-60230 and E4400-60597 for PSG/ESG Signal Generators Check Signal Gene

The default installation folder can be changed using the Browse button. 4. After installing both the PSG/ESG Upgrade Assistant 5.12 program and the selected firmware files, proceed to “Using the PSG/ESG Upgrade Assistant 5.12 with Firmware Files” on page 11. To install PSG/ESG Upgrade Assistant 5.12 and firmware files from CD-ROM 1. Insert the firmware upgrade CD-ROM into the computer’s CD-ROM drive. An autostart file should run automatically. 2. Once the PSG/ESG Upgrade Assistant 5.12 starts, p

Use the cable and adapter to connect Agilent instruments with 9-pin male RS-232 connectors to most PCs or printers. The cable kit contains: □ Null modem cable, 9-pin F to 9-pin F, 2.5 meters (8 ft. 2.5 in.), Agilent Part Number F1047-80002. □ Adapter, 9-pin M to 25-pin F (straight through), for PCs and printers, Agilent Part Number 5181-6641. □ This Reference Guide, Agilent Part Number 34398-90001. Agilent 34399A RS-232 Adapter Kit Contains four adapters to change a 9-pin female Null Modem (

r Products Tested The following Agilent instruments have been tested to operate properly with a PC, printer, and modem using the cable and adapter kits. • 33120A Function Generator /Arbitrary Waveform Generator • 34401A Multimeter • 53131A Universal Counter Cable and Adapter Pin Diagrams The following diagrams show the pin connections for the Null Modem cable (part number F1047-80002) with each of the adapters. Instrument DCD 1 - RX 2 - TX 3 DTR 4 GND 5 DSR 6 RTS 7 CTS 8 R

For those who wish ordering convenience, complete bundled systems are available. Whether ordering individual components or a bundled system, all 8510C network analyzers include one-year, on-site service. For systems built from individual components, installation may be ordered separately. A PC running BASIC Rev 6.3 or higher under Windows® (3.1/95/NT) is recommended for installation and service. Complete systems Agilent 8510XF family 110 GHz single sweep systems (45 MHz to 110 GHz) The 8510XF fa

At least 4Gb or higher. The USB cable is an Addonics USB 2.0 interface cable. The process involved A. Set up the USB drives under DOS mode (step 1 - 9) B. Copy folders and files from your Windows installation CD to the hard drives (step 10 - 17) C. start the software installation Installing Windows 2000, XP, 98SE or Me using the Addonics USB CD-ROM, DVD-ROM, DVD/CDRW or DVD-R/RW drive. 1. Download USB DOS driver and Save the file to your hard drive. 2. Use Winzip to extract the file, if you do n

No data will be lost if one of the drives fails. Mirror-Striping (RAID 0+1) Combined both Striping and Mirroring technologies to provide both the performance enhancements that come from Striping and the data availability and integrity that come from Mirroring. RAID 1+S (Mirrored-Sparing) Can automatically replace the failed drive and rebuild the system when booting HDD failed. Important Note: • To do a RAID SET, you can press F4 or CTRL+S from the boot up screen. Read and follow the instructi