Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
The Kengsington Lock System is a security system from Kensington Technology Group (that discourages the theft of portable computers and other devices (in this case touch panels) by using a security cable and lock to anchor the panel to an object in the room. The security cable is looped through a permanent object in the room, then looped through itself and locked into the slot. Once secured in this way, the panel cannot be removed from its location unless it is unlocked (using the key that comes with the Kensington Lock assembly). The NXA-KLB Bracket attaches to the base of the Table Top 1200V and VG-Series panels (listed below) using keyed-lock securing screws that can only be removed with the included AMX Keyed-Lock screw driver adapter. This screwdriver head fits into most hex-type screwdrivers or electric drills. There are two versions of the Bracket included with the kit, as indicated in FIG. 1: • The Flat Lock Bracket fits neatly into the rear of the panel’s base, allowing you to close the rear connector plate cover on the base while the panel is secured. • The Raised Lock Bracket also allows you to use the Kensington Lock System to secure the panel, while providing a surface to which you can secure incoming cables. Product Specifications Preparing the Touch Panel to Install the NXA-KLB 1. Gently place the touch panel LCD facedown onto a soft cloth to expose the under-side of the base and prevent scratching of the LCD (FIG. 2). • You may find it easier to handle the panel if you carefully detach all connectors. 2. Tilt the base forward so that the bottom surface of the base is easily accessible. This provides access to the underside of the unit and exposes the securing location for the Kensington Lock Bracket (FIG. 2). 3. Determine which type of bracket (Raised or Flat) you will be installing: • If your installation requires secured cables, use the Raised Lock Bracket. • If your installation requires a low-profile security solution, use the Flat Lock Bracket. Method A: Installing the Raised Lock Bracket Note that once installed, the shape of the Raised Lock Bracket will not allow the Connector Plate Cover on the base of the panel to be closed. 1. Raise the Connector Plate Cover, and align the openings on the bottom of the Raised Lock Bracket to the securing locations on the Base Plate of the panel (FIG. 2). 2. Insert two Keyed-Lock Securing Screws into their respective locations (FIG. 3). 3. Use the Keyed-Lock screwdriver adapter to tighten these screws, securing the Raised Lock Bracket to the base plate (FIG. 4). 4. Thread the incoming cables through the opening between the bottom of the Raised Bracket and the Base Plate (FIG. 4). 5. Reconnect the cables (on the rear connector plate). 6. Thread a tie-wrap (not included) through the center pair of circular openings on the bracket (FIG. 5) and use it to secure all of the NXA-MTC/RGB cables to the bracket. Trim off any excess length on the tie-wrap (if necessary). FIG. 1 NXA-KLB Components NXA-KLB Specifications Compatible AMX Touch Panels: • NXT-1200V, 12" Modero Video Table Top Panel (FG2250-60) • NXT-1200VG, 12" Modero Multimedia Table Top Panel (FG2250-61) • NXT-1500VG, 15" Modero Multimedia Table Top Panel (FG2252-61) • NXT-1700VG, 17" Modero Multimedia Table Top Panel (FG2257-61) Requirements: • The NXA-KLB must be used with a standard Kensington Lock System Note: The Kensington Lock System must be purchased separately, and is not provided by AMX. Included Accessories: • Raised Lock Bracket (with cable tie down) (black) • Flat Lock Bracket (black) • AMX Keyed-Lock screwdriver adapter • Keyed-Lock Securing Screws (5) Raised Lock Bracket Flat Lock Bracket Keyed-Lock Securing Screws AMX Keyed-Lock screwdriver adapter (fits into any standard hex-type screwdriver or drill) FIG. 2 Location of the securing locations on an NXT (Table Top) panel FIG. 3 Raised Kensington Lock Bracket Components and Installation FIG. 4 Raised Securing locations Base plate Connector plate cover (open to access the Securing locations for Kensington Lock Brackets Touch Panel glass (facing down) connectors on the rear of the base) Raised Lock Bracket Keyed-Lock Securing Screws Kensington Lock/Security Cable assembly (not included) AMX Keyed-Lock screwdriver adapter Connector plate cover Securing locations Thread incoming cables through this Base Plate Raised Lock Bracket Kensington Lock/Security Cable assembly (not included) opening between the Bracket and the Base AMX Corporation reserves the right to alter specifications without notice at any time. For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s). 036-004-2870 4/05 ©2005 AMX Corporation. All rights reserved. The AMX logo is a trademark of AMX Corporation. AMX reserves the right to alter specifications without notice at any time. 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • 93-22...