Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Step 2: Connect one end of the yellow cable ( ) to your modem, and connect the other end to your router. Power on your router. Wait until the wireless LEDturns on. Step 6: Insert Your CD. Click Router Setup and follow the steps to set up a securewireless network. Step 5: N300 Wireless Router(not included) Power on/offResource CDLaptop or DesktopComputerWireless on/offWireless N 300+ Powerline AV Router WNXR2000Note: If your laptop does not have a CD drive, see “No CD Drive” Installation on the back to complete your router setup. Step 7: Connect your Powerlinedevices. See next page. Step 3: Power on your modem. Wait until your modem cycles on (approximately2 minutes). Note: If you have a modem with a battery-backup, remove and re-insert the battery before connectingyour modem to power. Connect your computer. Connect with a wired connection (as shown in this diagram) orconnect wirelessly to the routerwith these settings: Wireless Network (SSID): ______________ Wireless Password: ___________________ Existing Powerline Network — Room 1 (example) Existing Powerline Network — Room 2 (example) Reset(additional Powerlineadapters not included) Setting Up Internet Access 1. In the address field of your browser, type and click Enter. 2. Enter the router User Name admin and default Password password to open your router’s main settings page. 3. When the main settings page opens, you will be asked if you want to “Check for Update.” Click Cancel. You can always check for new firmware later after you are connected to the Internet. 4. Select the first menu item on the left: Setup Wizard. Make sure Yes is selected. Then click Next and follow the prompts to complete the Setup Wizard. When the Setup Wizard has completed detecting your connection, the Basic Settings page displays showing your settings. You are now connected to the Internet. Note: If your ISP requires that you enter a User Name or Password, you will be prompted to enter this information. If you do not have this information, contact your ISP. Setting Up the Wireless Security 1. From the main menu page, select Wireless Settings.* *Your router menu may display different or additional features not shown 2. First, name your wireless network. Choose a name that is easy for you to remember. You might want to write it down here: ___________________________ (the default name is NETGEAR). 3. Select your security method. NETGEAR recommends WPA- PSK (TKIP) +WPA2-PSK (AES). Then, enter a Passphrase. In the example, we entered HomeNetwork. You might want to write your Passphrase down here:________________________. Note: Both your Network Name (SSID) and Passphrase are case sensitive. Your Network name, Security method and Passphrase must be the same on all the wireless devices connected to your router. 4. Click Apply and close your browser. Connecting Wireless Devices to Your Router 1. Open the wireless software that manages your wireless connections on the wireless device (iPhone, laptop computer, gaming device) that you want to connect to your router. 2. The wireless software will scan for all wireless networks in your area. Look for your network—the one you named when you set up your router. Select it. 3. If you set up security, you will be prompted for a Passphrase or network key. Enter the Passphrase you selected and click Connect. 1. Press the WPS button on the router. It will look similar to or . 2. Within 2 minutes, follow the wireless software instructions on the wireless device to complete the WPS process. The device will then be connected to your router. Repeat this process to add other wireless devices. LED and Button Descriptions WNXR2000 Router Status Lights •Solid Green. The power is on and the router is ready. •Solid Amber. The router is performing the power-on self- test diagnostic. •Off. Power is not being supplied to the router. •Solid Green. The wireless router has acquired an Internet address. •Solid Amber. No IP address acquired. •Off. No Ethernet cable is connected to the modem. •Solid Blue. The wireless interface is enabled. •Off. The wireless interface is turned off. •Solid Green. The local port is connected to a 100 Mbps device. •Solid Amber. The local port is connected to a 10 Mbps device. •Off. No link is detected on this port. •Solid Green. Indicates that wireless security (WEP, WPA-PSK, or WPA-PSK) is on. •Off. No WPS connection exists. XAVP1000 Adapter LEDs and Buttons •Solid green. The electrical power is on. •Blinking green.The adapter is restarting or setting up security. •Amber. Power saving mode. •Off. There is no electrical power. •Solid. The adapter is connected to a Powerline network. •Blinking. The adapter is sending or receiving data. •Off. The adapter has not found any other compatible Powerline devices using the same encryption key. •Solid. The Ethernet port is linked, but there is no activity. •Blinking. There is traffic on the Ethernet port. •Off. There is no Ethernet connection. Warning: Do not press th...