Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Netzwerk - WNR612v2 (3.24 mb)
Netzwerk - WNR612v2 (3.03 mb)
Anleitung Zusammenfassung
Within 2 minutes, follow the wireless software instructions on the wireless device to complete the WPS process. The device will then be connected to your router. Repeat this process to add other wireless devices. Note: Your network name, security method and passphrase must be the same on all wireless devices connected to your router. Enter your wireless information here: Wireless Network Name (SSID) Wireless Security Passphrase If you forget your Passphrase, connect a computer to the router using an Ethernet cable and log in to and enter the default User Name (admin) and Password (password). Restore Factory Default: For some routers, you may need to reset the device to its factory default first, then reconfigure your Passphrase. To restore factory defaults, use a paper clip to press the recessed reset button on the back until the Power/Test light blinks. This takes about 10 seconds. Release the button and wait for the router to reboot. Log in with the default username (admin) and password (password). Note: Restoring factory defaults will erase any customizations and you will lose any configurations saved to the device! LED Activity Item Description Power /Test • Blinking green: Router is performing the power-on, self-diagnostic test. • Solid green: The router is ready. Wireless • Solid green: Wireless connection is established. • Blinking green: Data is being communicated. • Off. The wireless interface is turned off. Internet • Solid green: Wireless router has a valid (Blue RJ-45 link on the internet or WAN port. connector) • Blinking green: Data is being communicated. • Off: There is no Ethernet cable connected to the modem. LAN Ports • If a LAN light is off, be sure the Ethernet (YellowRJ-45 connectors) cable is securely attached at both ends, and that the computer is turned on. • Solid green: Local port is connected to a 10 or 100 Mbps device. • Blinking green: Data is being transmitted at 10 or 100 Mbps. Technical Support Installation Guide Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at Wireless-N 150 Router Registration is required before you can use the telephone support service. Registration WNR612v2 via our website is strongly recommended. Go to for product updates and Web support. Package Contents For additional information about setting up, configuring, and using your Product Name Only, see the User Manual. For complete DoC please visit the NETGEAR EU Declarations of Conformity website at: a_id/11621/ GPL may be added in this product; go to ftp://downloads.netgear.com/files/GPLnotice.pdf to view the GPL license agreement. This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive. ©2010 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. September 2010 Router Configuration Set up internet connection 1. In your browser address field type and click Enter. 2. When the first screen opens, if you would like help setting up your wireless network, select the button next to “Yes, please guide me through the options.” If you are an advanced user and prefer to manually configure your router, select the button next to “No, I am an advanced user...” Then click Next. Set up wireless security 1. Select a wireless mode. (The default value is 150 Mbps: Performance Mode, which gives you the maximum wireless speed.) Click Next. 2. Now, select your wireless security method. NETGEAR recommends WPA-PSK [TKIP] + WPA2-PSK [AES] (the default value that is already selected). 3. Choose a Passphrase. You might want to write it down in the area provided on the middle panel. (Example: HomeNetwork). You have the option to print this screen. Click Next. Note: Both your network name (SSID) and passphrase are case sensitive. 4. Review your network settings on the summary page. You may want to print this for your records. Click Next to apply all settings and continue to follow instructions in the next section. Connect Wireless Devices to your Router 1. Open the software that manages your wireless connections on the wireless device that you want to connect to your router. (For example, on Windows XP, go to Control Panel ->Network Connections, right click the wireless device and select View Available Wireless Networks). 2. The wireless software will scan for all...